滚动轴承的理论旋转轴心线，对向心轴承即内圈轴心线，对推力轴承则指轴圈轴心线。
Rolling theoretical rotation axis line of the inner ring to the center axis line of bearings, thrust bearings on the shaft circle refers to the axis line.
双向压力球轴承有安装于轴上的中间圈和两个外圈，在中间圈与外圈之间分别加有钢球，能够承受双向轴向负荷。
Two-way pressure has mounted on ball bearings between the shaft and two outer rings, in the middle ring and outer ring were added between the steel ball, able to withstand the two-way axial load.
可以使用加大芯轴的尺寸，允许同时起到支承簧圈的作用。
Can be used to increase the size of the core shaft, allowing to play the role of the support spring.
轴抛：一种抛圈动作。在动作中，圈是绕着它的水平轴线旋转。
Axis throw: a hoop throws where the hoop spins around its horizontal axis.
由于套圈会和机器的圆轴保持一致，所以这种情况对于检测安装好的轴承并无影响，但当在安装前测量就应被注意到。
Since the rings adapt themselves to the round form of the matching parts, this circumstance has no effect on the installed bearing, but it is noticed when measuring the bearing before installation.
本文论述的是在“三峡旅游经济圈”的构建过程中“点——轴”式开发的问题。
The thesis discusses the important problem about dot-axis development in forming of Three Gorges Tourism Economy Circle.
对于推力轴承，与轴紧配合并一起运动的称轴圈，与轴承座或机械壳体孔成过渡配合并起支承作用的称座圈。
For thrust bearings, and shaft tight and together with the movement of said shaft washer, and bearing or mechanical shell holes into the transition and play supporting role with the said seat.
根据梯度分析的结果，提出环渤海经济圈城市之间的经济合作可以采取双核—圈层—轴带的模式。
According to gradient analysis results, proposes that the economic cooperation among the cities in Bohai sea surrounding economic circle can take dual-core, circle, axis pattern.
所述的预定力加载装置由加载法兰、用于轴定位的轴承挡圈和在轴承挡圈和加载法兰之间的线弹性垫圈组成。
The predetermined force loading device is composed of a loading flange, a bearing ring for positioning the axis, and an elastic washer arranged between the bearing ring and the loading flange.
形圈链条中销轴和套筒的磨损主要以疲劳磨损为主，并伴随着粘着磨损；
The bushes and bearing pins of the rubber O ring roller chains were characterized by stress fatigue wear and adhesion wear;
输入轴碳封圈密封面产生浮泡；碳封圈报废。输入轴上的密封面划伤，研磨修复。
Input seal: input carbon seal was blistered on the sealing face; the input carbon seal was scrap. Sealing face on the input shaft was scratched, and was lapped.
现在，我们就可以将望远镜饶x轴旋转360度，从而观察（以望远镜为中心的）水平包围圈的所有方向。
The telescope can then be rotated around 360 degrees in X axis so that it can scan the horizon in all the directions of the compass.
输入轴与齿圈（蓝色）连接，输出轴与行星架（绿色）相连，行星架上装有多片离合器。
The input shaft is connected to the ring gear (blue); The output shaft is connected to the planet carrier (Green) which is also connected to a "multi-disk" clutch pack.
压球机零件有中空轴、齿圈轮、小齿轮、辊皮、电机等。
Pressure ball machine parts have hollow shaft, wheel, small gear tooth circle, roller skin, motor, etc.
在联轴结和电动机之间装有密封圈，可防止水和牙膏等进入机体。
A sealing ring is arranged between the motor and the coupling, so water, toothpaste, etc. can be prevented from entering a machine body.
本公司主要生产铆钉、螺栓、螺母、平垫、弹垫、挡圈、销轴平键等系列配套产品。
Our company mainly produces series of accessory products as rivets, bolts, nuts, flat washers, spring hooks, stoppers and axis pin & flat keys etc. all the products strictly follow national standards.
搅拌轴上的搁圈装置限制了搅拌轴的下坠。
A loop placement device on a stirring shaft limits the falling of the stirring shaft.
轴承内圈(轴圈)的基本圆柱孔或圆锥孔的内接圆柱体或内接圆锥体的轴心线。
Bearing inner ring (shaft circle) of the basic cylindrical hole or holes in the internal tapered cylinder or cone in the axis line access.
阀门轴径密封采用石墨压制成形密封圈。
The sealing performance of valve is not influenced uses pressed graphite sealing ring .
黄河流域人口空间分异呈现出“点轴圈”的空间结构模式。
The population spatial distribution took on the form of"pole-axle-circle"pattern.
黄河流域人口空间分异呈现出“点轴圈”的空间结构模式。
The population spatial distribution took on the form of"pole-axle-circle"pattern.
应用推荐