适用于测量干燥且无腐蚀气体的差压压力。
Suitable for testing differential pressure of dry and non-corrosive gases.
其中保压时间、冷却时间及保压压力是最重要的因子。
The packing time, cooling time and packing pressure are the most important factors.
在大量实验结果的基础上探讨了最优保压压力曲线的设定。
The effect of the size of particulates and pressing pressure on porosity ratio has been studied.
结果发现，收缩压和舒张压压力均低于人们谁曾家血压监测。
It was found that systolic and diastolic pressure were both lower in people who had home blood-pressure monitoring.
当球落在坐放座上时，通常施加液压压力，以操纵工具机构。
When the ball is located on a landing seat, hydraulic pressure generally is applied to operate the tool mechanism.
轮框是在一个有125度高温和6个气压压力下在真空焗炉铸造的。
The wheels are cured in an Autoclave at 125 degrees C and 6 bar of pressure.
出力调整容易，只需调整气压压力，就可达到所需要的压力，简单方便。
Easy to adjust the the output; the required pressure can be reached by simply adjusting the pneumatic pressure; easy and convenient.
它有四个主要的机械位移，其速度可以调整，由液压压力与无级调速改变。
It has four mechanical shifts, and its speed could be adjusted by hydraulic pressure with stepless speed change.
本文研究了挤压铸造时不同加压压力对铝合金结晶组织和机械性能的影响。
In this paper, the effects of pressurizing value on aluminum alloy crystal structure and the mechanical properties in squeeze casting process have been studied.
液压系统向连铸机升降驱动辊供给的液压压力应根据工艺要求进行设定计算。
The hydraulic pressure which hydraulic system provides to the pinch roll in CC machine should be set-up and calculated according to CC process requirement.
一般地，经油管柱施加液压压力而不是由操纵油管柱施加机械力使封隔器坐封。
A hydraulic packer typically is set using hydraulic pressure applied through the tubing string rather than mechanical force applied by manipulating the tubing string.
确定了经济性优化的原则，建立了经济性优化的叶片位置脉谱和增压压力脉谱。
Economy optimizing rule is determined and the map of vane position and boost pressure is obtained.
随着环境的变化，热泵热水机将出现冬季结霜，夏季出现低压压力过高的现象。
With the change of environmental temperature, the air sourced heat pump water heater will frost in winter and the low pressure will be too high in summer.
研究表明：涂胶量的影响显著，热压温度、热压时间和热压压力的影响不显著。
The result shows that adhesive content is vital, but unit press and temperature and time of hot press are minor to the variance of warp degrees.
采用液压机和先进的数据采集系统对模压压力影响焦炭粉体的堆积密度进行了研究。
The effect of molding pressure on packing density of coke powders has been studied in a hydraulic press machine with advanced data-collected system.
全自动化控制系统，高低压压力保护，电源断相及逆相保护，有效保障压缩机运行。
Fully automated control system, high and low pressure protection, power off phase and reverse phase protection, effective protection of compressor.
研究了掺杂剂用量、模压压力、模压温度、氧化剂用量对聚苯胺盐电导率的影响。
The effects of the content of the dopant, moulding pressure and temperature and the content of oxidant on the conductivity of PANI were studied.
静压是差压表两个检测点所在管道内的设计压力。它是差压压力表选型时必需的数据。
Static pressure is the designed pressure difference within the pipeline between two testing points. It is a necessary date when selecting different types of pressure gauges.
运用较大热压压力的制板工艺，可以在一定程度上提高导电功能刨花板的电磁屏蔽效能。
A higher pressing pressure can improve electromagnetic shielding effectiveness of conductive particleboard to some extent.
结果表明，气体冷却器出口温度、过热度和膨胀机效率对最优高压压力的影响较为明显。
It is illustrated that discharge temperature of gas cooler, efficiency of expander and degree of superheat at the inlet of compressor can exert more influence on the optimum high pressure.
模压压力对接触电阻已有一定程度的影响，但其影响幅度不如接触压力和树脂含量那么大。
The compression pressure and temperature had a smaller influence on contact resistance compared with contacting pressure and PF content.
温度、注射速度、注射压力和注射成型过程的保压压力是获得较高制品质量的重要影响因素。
The temperature, injection speed, injectionjectio n pressure, and holding pres sure of the injection molding process should be controlled to achieve high quality of injection molded part.
每个热水供暖锅炉都必须配置压力安全阀，其设置的泄压压力必须小于锅炉的最大工作压力。
Must not be rated higher than the working pressure shown on the data plate of the water heater.
每个热水供暖锅炉都必须配置压力安全阀，其设置的泄压压力必须小于锅炉的最大工作压力。
Each hot water space heating boiler shall be equipped with a pressure relief valve set to relieve below the maximum boiler working pressure.
试验结果表明，气囊充压压力使复合材料承力筒的壁厚减薄，纤维体积含量增加，弯曲性能提高；
The experimental result shows that higher bladder pressure decreases thickness of composite bearing cylinder, increases fiber volume fraction and improves the bending properties.
此外，断口形貌的SEM观察表明，随保温时间的延长或热压压力的提高，复合材料界面层变厚。
The SEM fractographs show that the composite interfacial films between the fibre and the matrix are thickened with the increase of the hot-pressing time or pressures.
此外，断口形貌的SEM观察表明，随保温时间的延长或热压压力的提高，复合材料界面层变厚。
The SEM fractographs show that the composite interfacial films between the fibre and the matrix are thickened with the increase of the hot-pressing time or pressures.
应用推荐