作者为此研制了一种强化自动清洗力矩的斜齿扭带。
Therefore, the author has improved slantwise rack strip with auto-cleanout strengthen moment.
测出产生力矩的电流，然后根据事先校正的数据来算出飘移率。
The torquing current is measured and related to drift rate by prior calibration data.
在下一章，我们将说明用力矩的概念求解这个问题的另一种方法。
In the next chapter we shall explain another method of solving this problem, using the concept of the moment of a force.
提出了车辆转向时，车轮转向阻力矩及围裙转向阻力矩的数学模型。
The mathematical models on turning resistance moment of the wheels and apron against ground are put forward.
本文提出了一种在时域上设计柔性机械臂开环控制力矩的逆动力学方法。
In this paper, the new inverse dynamics method, which designs the open-loop control torque for one-link flexible manipulator, is proposed.
由于采用了电流负反馈控制方式，制动力矩的大小可根据需要进行控制。
Due to electric current negative feedback control, the intensity of braking torque can be controlled as it is needed.
对极限承载力计算中次力矩的效应提出了设计建议，可供结构设计应用。
Finally, the effect of secondary moment at the ultimate limit state design has also been suggested.
文中分析了其大幅度降低的原因，并推导出求轧制力和力矩的简化公式。
The reasons of rolling force and torque reduction are discussed. Also the simplified formulas of rolling force and torque are derived.
对于任何成功的营销沟通，你需要获得的信息，市场，媒体和力矩的权利。
For any successful marketing communication you need to get the message, market, media and moment right.
建立了拖拉机起步过程中机组、发动机、离合器和机组阻力矩的数学模型。
The mathematical models of tractor set, engine, clutch and the moment of tractor set resistance during the tractor starting have been set up.
对驱动性能进行了分析，结果表明驱动力矩的频段与噪声信号频段是分离的。
Driving performance analyses show that the frequency spectrum between driving moments and noise signals is separated.
分析了相对密度比、深度比、波幅、波长因素对最大总作用力和总力矩的影响。
Moreover, the effects of density and depth ratio, amplitude and wavelength on maximal total force and total moment are analyzed.
基于磁性能分析计算的复杂性，提出了一种计算永磁齿轮传动力矩的有效方法。
Based on the complexity of analysis and calculation of magnetic behavior, an efficient method is put forward for the torque calculation of permanent magnetic gears.
结果表明：制动盘端面跳动最终以虚拟制动盘厚度变化形式引起制动力矩的波动。
The results show that disc side face run-out results in brake torque variation by means of disc thickness variation.
叶片水力矩的变化与泵性能参数的变化密切相关，应引起泵设计人员的充分重视。
The change of hydraulic moment on blades is closely related with pump characteristics, which should arouse the attention of pump designers.
通过对船在波浪中所受表观重力和表观浮力的分析，导出波浪作用力矩的计算公式。
In this paper, by analyzing the apparent gravitation and apparent buoyancy to ship in wave, a formula calculating moment by wave has been derived.
介绍了摩托车制动器操纵力和制动力矩的测量方法，分析了对测量精度的影响因素。
The methods for measuring control force and brake torque of the motorcycle brake are introduced and the factors affecting precision are analysed.
而转向半径、转向力矩和转向阻力矩的大小是衡量装载机转向性能的重要性能指标。
They are important data to judge steering function of loader such as steering radius, force moment of resistance and moment of steering.
给出计算结果与实验数据的比较，分析烧蚀滞后滚转力矩的模数随飞行参数的变化。
Comparisons between calculated results and experimental data are presented, the variations of module of the roll toque coefficients with flight parameters are analyzed.
该文建立了静电力矩的数学模型，确定了支承系统频率特性与静电力矩大小之间的关系。
A mathematical model of the electrostatic torque was used to analyze the relationship between the torque and the system frequency response.
理论分析表明：行星轮公转与自转的速比，影响着每个切削刀具的阻力矩的大小与方向；
Theoretical study shows that the ratio of revolution velocity to rotation velocity will affect the magnitude and direction of resistance moment of all the cutters.
并研究了姿控发动机的配置特点和点火逻辑，给出了由期望力矩计算实际控制力矩的方法。
The formula of anticipant control moment is deduced by adopting the method of exponent reaching law and twitter reducing of boundary layer.
仿真结果表明这种控制方法有效地抑制了多余力矩的干扰，提高了系统的鲁棒性和跟踪性能。
The simulation results show that this kind of the control law can decrease the disturbance torque effectively and improve the robustness and tracking property of the system.
当她调至低档了一个工具的时候，她伸展出而且墬落，而且向后有突然推进和转力矩的高尖叫。
She stretched out and down, and there was a sudden backwards thrust and the high squeal of torque as she downshifted a gear.
提出了一种有限维重复控制方法，以实现对有严重非线性扰动力矩的伺服机构的高精度速率控制。
A finite dimensional repetitive control method is proposed for the high precision velocity control of servomechanisms subject to significant nonlinear disturbance torque.
提出了一种有限维重复控制方法，以实现对有严重非线性扰动力矩的伺服机构的高精度速率控制。
A finite dimensional repetitive control method is proposed for the high precision velocity control of servomechanisms subject to significant nonlinear disturbance torque.
应用推荐