转子在其凸角之间的三个面上有凹槽。
The rotor has recesses in its three faces between the lobes.
在这种布置中，凸轮凸角推动凸轮挺杆。
In this arrangement, the CAM lobes push against round metal cylinders called CAM follower.
在这种布置中，凸轮凸角推动凸轮挺杆。
As the lobe of the CAM comes up under the CAM follower, it pushes the CAM follower upward (away from the camshaft).
凸轮轴上有一个凸轮，凸轮上有一个凸角。
控制进气阀的凸轮上的凸角在阀挺柱向下回转。
The lobe on the CAM controlling the intake valve has moved out from under the valve lifter.
在此基础上，提出了剃前滚刀凸角尺寸修改的建议。
On the base, it also put forward the suggestion to correct the convex Angle size of preshaving hob cutter.
胸椎后凸角值随年龄的增大而增大，符合生理性改变。
The posterior convex Angle of thoracic vertebrae was increasing with the age and physiological change.
新骨折发生于有明确外伤史及术后随访局部后凸角较大的患者。
New fracture easily occurred in patients suffered from injury, and whose local kyphosis Angle is greater.
螺钉松动患者的内固定物位置无进一步变化，但胸椎后凸角度加大。
No further position change of the instrument was noticed in the patient carrying loosened screw, but the kyphosis of the thoracolumbar spine aggravated.
凸角侧向腐蚀程度与腐蚀深度、腐蚀温度、腐蚀剂配比等诸多因素有关。
It was relative to the etching depths, temperature and the etchant proportion and types.
当凸轮轴转动时，凸轮凸角转到气门挺杆下面，使挺杆上举，挺杆推动推杆。
As the camshaft turns, the CAM lobe comes around under the valve lifter. This raises the lifter, which in turn pushes upward on the push rod.
当凸轮的凸角在凸轮挺杆下出现时，它推动凸轮挺杆向上运动(离开凸轮轴)。
As the lobe of the CAM comes up under the CAM follower, it pushes the CAM follower upward (away from the camshaft).
当凸轮的凸角在凸轮挺杆下出现时，它推动凸轮挺杆向上运动(离开凸轮轴)。
After the CAM lobe moves out from under the valve lifter, the valve spring forces the valve up onto its seat again.
曲轴上凸轮凸角的位置使气门在恰当的时侯开关，以便与气缸的工作顺序相一致。
The CAM lobes are so positioned on the camshaft as to cause the valves to open and close in the cylinders at the proper time with respect to the actions taking place, in the cylinders.
手术后和最后随访时相比，局部后凸角和PF A评分的改善方面的差异有统计学意义。
A statistically significant improvement in local kyphosis angles and PFA scores was found after surgery and at the last visit.
两个单元间的干扰(凸角)会在该频率周围产生功率响应急降，并由于方向性的差异而产生一个峰值。
Interference (or 'lobing') between the two units causes a dip in power response around this frequency, with a peak above it due to their differences in directivity.
当坡度较大时，最小值出现在距凹角约为0.5倍步长处，最大值出现在凸角附近，且凸角压强没有明显降低。
The minimum point is in the distance of 0.5 time pace from the nook while the maximum point is around the salient when the grade is big.
结论：骨质疏松患者的脊柱畸形主要表现为脊柱的局部后凸尤其是胸段脊柱后凸角度的增大，其中又以凹圆背畸形最为多见。
Conclusion: the spinal deformities in osteoporotic patients are characterized by the local kyphosis of spine, especially thoracic kyphosis, and hollow round back is the most common deformity.
两个凸轮凸角之间的切换系统，是通过ECU对引擎的油压、温度、行驶速度、引擎转速和节油门位置的综合计算，而实现对其的控制的。
The switching operation between the two cam lobes is controlled by the ECU which takes account of engine oil pressure, engine temperature, vehicle speed, engine speed and throttle position.
结论：椎间盘高度、腰椎小关节角、椎间盘前凸角等形态结构变化对腰椎节段有限元模型的峡部、小关节应力及小关节接触力有明显的影响。
Conclusion the variation of the disc height, facet-joint Angle and the lordosis Angle of the intervertebral disc had a manifest influence on the isthmic stress and facet contact force.
以一种梁-质量块结构的加速度计为模型，为了在加工过程中，得到完整的质量块结构，使结构具有更好的对称性，对各种凸角补偿方式进行了研究。
To acquire intact mass structure with better symmetry, various methods of convex corner compensation were studied based on a sort of accelerometer of beam-mass structure.
以一种梁-质量块结构的加速度计为模型，为了在加工过程中，得到完整的质量块结构，使结构具有更好的对称性，对各种凸角补偿方式进行了研究。
To acquire intact mass structure with better symmetry, various methods of convex corner compensation were studied based on a sort of accelerometer of beam-mass structure.
应用推荐