然而安装一个齿轮减速器后，涡轮可以高速驱动低速运转的风扇。
A gearbox, however, allows the turbine to operate at a high speed while driving the fan at a lower speed.
这种发动机在风扇与涡轮间安装了一个齿轮减速器。
Unlike a conventional turbofan, it USES a gearbox rather than a shaft between the fan and the turbine.
项目资金将用于购买长期材料和主要设备，比如主减速器等，以支持新舰的初步设计和规划。
The funds will be used to purchase long-lead time materials and major equipment, such as the main reduction gears, in support of the new ship and to perform initial design and planning.
检查提升卷扬机减速器，按照要求加注规定油面高度。
Test the lift hoist reducer and pour the oil according to the demands.
本文对渐开线点啮合齿轮减速器进行了性能试验、接触疲劳强度和弯曲疲劳强度试验，同时还进行了铁谱分析。
This paper describes the performance test, contact fatigue strength test and bending fatigue strength test on the gear reducer of involute point contact Ferrographical analysis is made.
基于减速器的齿轮、轴、轴承、及其校核，文章给出了设计和计算。
Based on the gear reducer, shaft, bearings, and checking, the article gives the design and calculation.
新产品系列中样机试验的结果也验证了其比原规格大小的三环减速器的承载能力有了很大提高。
The experiment results of sample reducer prove that the loading capacity of new designed product series is much higher than primary one under the same condition.
大模数重载汽车主减速器盆形齿轮经渗碳淬火后，齿轮齿面经常会出现裂纹。
Cracks frequently generated in basin gear of big modulus main reducer used in heavy load truck after carbonizing and quenching.
本设计说明书设计了减速器。
以减速器设计为例阐述基于实例设计中实例表示、实例检索、实例修改、实例存储的关键技术。
Many key techniques about case based design which include case representation, case retrieval, case adaptation and case maintenance are discussed by using an example of reducer design system.
分析了直升机主减速器齿轮电刷镀修复后产生裂纹的成因，通过试验提出了喷丸强化改进措施。
The cause of cracks after brush-plating on the main speed reducer of helicopter was analyzed and the ameliorative measures by shot-peening were brought forward consolidation.
本文研究摆线钢球减速器关键技术之一，无侧隙啮合副共轭齿形综合问题。
The paper researches one of the key techniques of the cycloid steel ball reducer, that is the synthesis of conjugate waves shapes for no gear clearance engagement pair.
本文旨在设计新的三环减速器产品系列。
This dissertation is aimed to design a new product series for three-ring gear reducer.
接着对减速器的部件组成进行了尺寸计算和校核。
Then the components of the reducer to the size of the calculation and verification.
文中介绍了物流机械手的设计，此机械手采用电机减速器等实现运动功能，通过PLC控制各个运动部件。
The design of logistic manipulator is introduced. The moving parts of this manipulator was controlled by PLC. The motion function is implemented with motors and speed reducers.
本文以改善摆线针轮减速器轮齿啮合质量为目的，提出了一种新颖的摆线轮齿形修整方式。
This paper proposes a new method to modify the cycloid gear tooth of reducer in order to improve the gear engagement.
本文结合圆柱齿轮减速器的优化设计，讨论了优化设计在机械零件课程设计中的应用。
This paper discusses the application of favorable design in machine parts curricula design by the favorable design of the column gear wheel reducer.
为谐波齿轮减速器的设计，提高其工作性能打下了良好的基础。
These could be good fundamentals for improving the design of harmonic gear reducer and their performances.
为了降低全寿命费用和增强飞行安全性，对减速器故障进行检测和故障诊断是非常必要的。
To reduce life cycle cost and to improve flight safety, the detection and diagnosis of gearbox faults is of vital importance.
减速器、制动器等起升装置。
回转机构由液压马达及蜗轮蜗杆减速器组成。
The slewing mechanism consists of hydraulic motor and worm speed reducer.
这些系统还可以用于大马达联轴节、减速器、离合器等的试验。
These systems can also be used in tests of large motor couplings, speed reducers, clutches, etc.
针齿壳销孔的加工是摆线针轮减速器制造的重要步骤之一。
Pinhole machining of pin gear housing is one of important procedures in manufacturing cycloid speed reducer.
减速器振动信号的冲击性振动信号往往可以与故障引起的冲击联系在一起，因此冲击性信号可以作为一个故障的表征形式。
Impulsive vibration signals in gearbox are often associated with impulse resulted from faults, and thus, impulsive signals can be used as the symptoms of faults.
通过现场测试总结并提出了一种易损减速器滚动轴承的故障诊断判据。
After site testing, we find a kind of problem diagnosing criterion for rolling bearings of damageable retarder.
本文基于蜗杆蜗轮减速器工作中振动信号的测量和分析，提出了一种蜗杆蜗轮减速器磨损状态的振动监测方法。
Based on the vibration measurement and analysis of worm gear reducer, a new monitoring method is put forward for wear of worm and worm wheel.
通过对旋转模头系统行星齿轮减速器故障分析，提出了相应的改造对策，同时对行星齿轮减速器的啮合参数进行了优化设计。
Based on analysis of malfunction of planet - gear speed reducer in rotating die system, this paper presented corresponding revamping measures, and optimized the design of its joggle parameters.
它由一个滑架、个转动齿轮减速器和一个提升齿轮减速器组成。
It consists of a carriage, a rotary gear reducer and a hoist gear reducer.
它由一个滑架、个转动齿轮减速器和一个提升齿轮减速器组成。
It consists of a carriage, a rotary gear reducer and a hoist gear reducer.
应用推荐