中等流量，低温韧性，紫外线稳定。
Medium flow, low temperature ductile, PC siloxane copolymer.
非常高的含量的低温韧性和焊接性能提高。
Very high levels of toughness at low temperature with improved weldability.
提高高纤维素型焊条低温韧性是未能解决好的一大难题。
It is a difficult problem to improve the low temperature toughness of high cellulosic electrodes.
结果表明，强度对淬火温度变化不敏感，而低温韧性则较敏感。
The results showed that the strength of the steel is not sensitive to the quenching temperature, but the toughness at low temperature is.
通过冲击试验，研究了水韧处理质量对高锰钢低温韧性的影响。
The effects of water toughening quality on the toughness at low temperature of high-manganese steel was studied using impact -tests.
通过调整合金成份和改变热处理制度试验，有效地提高了低温钢的低温韧性。
The low temperature toughness of low temperature steel can be improved effectively by means of adjusting alloy ingredients and modifying heat-treatment regime.
介绍喷涂聚脲弹性体的力学性能，耐介质性、低温韧性、耐老化性、附着力及其施工。
This paper introduces mechanical property, medium resistance, low temperature toughness, age resistance, adhesive tension and construction of sprayed polyurea elastomer.
结果表明，用这种工艺生产的船板具有高强度和良好的低温韧性，完全可以代替正火处理。
It is show that the ship-plates produced by these parameters have high strength and good low-temperature toughness, and the normalizing treatment is no longer necessary.
强度较高，且韧性、焊接性及低温韧性也较好，被广泛用于制造桥梁、锅炉、船舶等大型结构。
High strength, toughness, weldability and low temperature toughness is also widely used in the manufacture of Bridges, boilers, ships and other large structures.
在几乎不增加冶金成本的前提下，试制钢板具有优良的强度、塑性配合，优良的低温韧性水平。
With little increase in cost of steel making, the steel with good combination of strength and plasticity and satisfied toughness at low temperature can be produced by controlled rolling and cooling.
对金属茂聚烯烃(MPO)的许多优良特性，如透明性、柔韧性、低温韧性和热塑性弹性体行为等进行了综述。
A new family of metallocene-based polyolefine (MPO) is evaluated. Many properties of MPO, including clarity, flexibility, low temperature ductility and thermoplastic elastomer behavior are emphasized.
采用焊接热模拟技术、显微组织分析和冲击试验的方法，研究了焊接线能量对X70管线钢焊接热影响区组织和低温韧性的影响规律。
The effect of welding line energy on microstructure and low temperature toughness of heat-affected zone(HAZ) of X70 pipeline steel was studied by welding thermal simulation method.
其中针状铁素体之间细小的马氏体的存在与数量对钢的抗拉强度和低温冲击韧性起关键作用。
The existence and amount of small isolated martensite between the acicular ferrite play an important role in determining the tensile strength and low temperature impact toughness of the steels.
舞钢研制开发的调质钢wh80 Q具有高强度、良好的低温冲击韧性、抗层状撕裂性能、较低的时效敏感性系数。
The quenched and tempered steel WH80Q offers high strength, excellent low temperature impact toughness, lamellar tearing resistance and lower aging sensitivity factor.
试验结果表明，低温淬火工艺可使外套圈获得优良强韧性与耐磨性。
Test showed that the low temperature quenching process may cause the outer rings to have excellent and stable strength, toughness and wear-resistance.
考察了交联剂、增塑剂、制备工艺对沥青高低温性能、粘韧性、韧性的影响。
The effects of adding plasticizer, crosslinking agent and the blending process on the high-low temperature ductility, toughness and tenacity of asphalt were investigated.
挤出级的ABS（丙烯腈丁二烯苯乙烯）。具有超强的韧性非常高品位的影响，特别是低温应用，以及良好的热成型。
Lustran ABS 1152 Extrusion grade of ABS (acrylonitrile butadiene styrene). Very high impact grade with superior toughness, especially for low temperature applications, and good thermoformability.
两个时效峰的硬度和强度相差很小，在较低温度下时效第二峰的强度、硬度、塑性、韧性较高。
At lower temperature, the strength, hardness, plasticity and ductility of the alloy at the second ageing peak are higher than those at the first one.
结果表明，本钢X70管线钢具有高强度、高抗动态撕裂能力、高低温冲击韧性以及低韧脆转变温度。
The results indicate that the X70 pipeline steel with acicular ferrite microstructure has high strength, high toughness, low transition temperature and high dynamic tear-resistance.
在低温陶瓷结合剂中添加适量金属或合金粉，就会对结合剂的耐火度、流动性、热膨胀系数、强度等性能产生影响。通过试验分析，合金粉的加入能改善结合剂的强度及韧性。
When Added Additive, PEC, strength, the ratio of the thermal expansion and fluidity etc, of bond would be effected, through testing, strength and toughness of bond will proved with adding alloy.
有良好的低温冲击韧性和抗裂性能，焊接压力容器、水电站下降管、桥梁、海洋工程等重要结构。
It has excellent impact toughness on gap and crack resistance. It's used for welding key structure such as pressure containers, drop pipes of hydroelectric station, Bridges, ocean projects, etc.
金属材料韧性的丧失可以通过核查低温时的应力—应变的关系观测。
The loss of metal toughness can be observed by checking stress - strain relations at low temperature.
该流体机械尤其是用于低温用途的涡轮压缩机，其中该壳体优选地由具有马氏体组织的冷韧性的材料制成。
Said fluid machinery is designed especially as a turbo compressor for use at low temperatures, the housing preferably being made of a cold-resistant material that has a martensitic structure.
试验研究了石油机械铸锻件常用低合金钢的显微组织结构对低温冲击韧性的影响。
An experimental investigation was made on the effect of the microstructure on the low-temperature toughness of the conventional low alloy steel used for petroleum machinery castings and forgings.
晶粒细化显著提高了钢的低温冲击韧性。
Low temperature toughness is remarkably improved by grain refinement.
适用于焊接对低温冲击韧性要求高的重要焊接结构。
It can be suited to the important welded structures which have strict requirements of the low-temperature impact flexibility.
适用于焊接对低温冲击韧性要求高的重要焊接结构。
It can be suited to the important welded structures which have strict requirements of the low-temperature impact flexibility.
应用推荐