Welding current can be set to increase compensation.
可设定焊接电流递增补偿。
Welding current is transferred to the wire through the contact tip whose bore is slightly greater than the wire diameter.
焊接电流通过孔径稍大于焊丝直径的接触端传送到焊丝。
High ability in resisting public power grid voltage wave ang power grid compensation, stable welding current.
抗电网电压波动及电网补偿能力强，焊接电流稳定。
Contact mark. Intermittent marks adjacent to the weld line resulting from the electrical contact between the electrodes supplying the welding current and the pipe surface.
触点痕。由于供焊接电流的电极与管子表面间的电接触，致使在焊缝线附近产生不连续痕迹。
Arc voltage and welding current are signal source.
以电弧电压和焊接电流为采集的信号源。
The rotary driving circuit, position detecting circuit, and welding current sampling circuit of the high speed rotating arc sensor are introduced in detail.
详细介绍了高速旋转电弧传感器的旋转驱动电路、位置检测电路以及焊接电流采样电路。
The welding current can be reduced, which produces lower electrode temperature and enhances the electrode life.
可降低焊接电流，导致较低的电极温度从而提高了电极寿命。
Based on these fuzzy control forms, weld pool width is easily controlled by adjusting welding current.
以焊接电流为控制量，可以根据此控制作用表对焊缝熔宽进行实时控制。
Testing results show that the major factors affecting the deposition efficiency are the welding current, arc voltage and gas flow rate under the condition of same circuit inductance.
试验结果表明，在回路电感值不变的条件下，焊接电流、电弧电压和气体流量是影响熔敷效率的主要因素。
The PID adjuster of integration separation mode has been used in this system, which have good responsive speed and adjust property in the range of welding current.
系统采用积分分离式变参数PID调节器，在焊接电流调节范围内，具有良好的响应速度和调节性能。
The controlling system has many work patterns, such as manual, semiautomatic, and automatic, and can compensate for the effect of voltage fluctuation to welding current.
控制系统具有手动、半自动、全自动等工作方式，可自动补偿网压波动对焊接电流的影响。
By analyzing the variation of welding current, offset information obtained in order to achieve underwater seam tracking.
通过分析焊接电流的变化规律得到偏差信息从而实现水下焊缝跟踪。
Double reversed star shape, interphase reactor, flat wave output circuit, stable welding current.
双反星型，平衡电抗器及平波输出电路，焊接电流稳定。
The adaptive welding current adjuster based on the minimum variance theory is designed.
设计了基于最小方差调节的自适应焊接电流调节器。
The welding current control for inverter source is the key that meets requirements of varied welding processes and ensures the operation stability and reliability.
弧焊逆变电源输出电流控制是满足不同焊接工艺需求和保证电源可靠运行的关键。
The welding machine can make compensation to the voltage of power grid and maintain the stability of welding current in cold and hot conditions.
焊机对电网电压波动进行补偿，并在焊机冷热态时都能保持焊接电流的稳定。
The welding machine is convenient for operation and the welding current can be regulated by remote control.
焊机操作方便，可远距离调节焊接电流。
During the course of forming the welding spot, checking and controlling spot welding current value is the key to assure the welding quality.
在焊点形成的过程中，点焊电流有效值的检测与控制是保证焊接质量的关键。
Equipped with welding controller, the welder has precise control and setting functions for the welding time and intervals and welding current energy.
同时配备缝焊控制器，对焊接时间，间歇时间，焊接电流能精确的设定和控制。
When welding voltage is between 21v and 24v and welding current is between 210a and 270a, better welding line can be obtained.
发现超窄间隙焊的焊接电压范围在21 ~24v，电流在210 ~ 270a能够得到较好的焊缝成形。
Digitized PMIG welding is playing an important role in welding field for its advantages, such as good direction transition, less splashed material, nice figure and wide welding current extent.
数字化脉冲MIG焊以其可以在很大电流范围内获得射滴过渡、轴向性好、飞溅小、适合全位置焊等众多优点，在焊接领域中占有重要一席。
It has the welding current feedback circuit and the welding voltage feedback circuit.
具有焊接电流反馈控制电路及焊接电压反馈控制电路。
The large welding current caused the formation of quenched martensite and the high residual stresses in the welding zone, resulting in the increase of zinc sensitivity of hydrogen attack.
结果表明：由于焊接电流过大，使焊缝产生淬火马氏体组织及较大的焊接残余应力，导致镀锌氢脆敏感性增加，造成吸油盘发生氢脆开裂。
The design, analysis and testing of the welding current signal detecting circuit for spot welding machine are discussed in this paper.
本文主要论述点焊机焊接电流信号检测电路的设计、分析和测试。
The welding current, welding speed and the plasma gas flow rate were the most important parameters in the ending stage.
发现焊接电流、离子气流量和焊接速度对收弧过程影响较大。
Input preloading, wave head, welding time, the pressure, welding current parameters.
输入预压、波头、焊接时间、保压、焊接电流等参数。
The effect of welding current on pressed depth is above that of welding press and welding electrifying time.
焊接电流对压入深度的影响明显大于电极压力和焊接通电时间。
The accurate measurement of welding current and voltage is very important to the exact control of resistance spot welding inverter and welding quality.
焊接电流与电压的准确测量对精密控制逆变电阻点焊电源和保证焊接质量至关重要。
The accurate measurement of welding current and voltage is very important to the exact control of resistance spot welding inverter and welding quality.
焊接电流与电压的准确测量对精密控制逆变电阻点焊电源和保证焊接质量至关重要。
应用推荐