As shown in Figure 2, a system (cec2) is connected to the same network and has a vios partition (vios_cec2) that has access to the same SAN disks that are accessed by the vios partition (vios_cec1).
如图2所示，另一个系统(cec2)连接相同的网络，它有一个vios分区(vios_cec2)，可以访问vios分区vios_cec1所访问的SAN磁盘。
The next step was to boot the VIOS.
下一步是引导VIOS。
DS8300 VIOS pair (source) : hvio1 and hvio2.
DS8300VIOS对(源)：hvio1和hvio2。
NetApp VIOS pair (target) : hvio11 and hvio12.
NetAppVIOS对(目标)：hvio11和hvio12。
Source DS8300 VIOS pair names: hvio1 and hvio2.
源ds8300VIOS对的名称：hvio1和hvio2。
Target NetApp VIOS pair names: hvio11 and hvio12.
目标NetAppVIOS 对的名称：hvio11和hvio12。
To log in, use the VIOS padmin userid and password.
使用VIOSpadmin 用户 ID和密码登录。
I find the VIOS command line much faster and easier.
我发现VIOS命令行快得多，也更容易。
I noticed that the boot list on each VIOS had changed.
我注意到，每个VIOS上的引导列表改变了。
Verify that the same SAN disk can be seen by both VIOS.
确认两个VIOS都可以看到同一个SAN磁盘。
Run this command on the source VIOS during the migration.
在转移期间，在源vios上运行此命令。
These steps were to check the general health of the VIOS.
这些步骤检查VIOS的健康状态。
Document the current virtual device mappings on each VIOS.
记录每个VIOS上当前的虚拟设备映射。
The VM Library was introduced with VIOS 1.5, back in 2007.
VM库是 2007 年在VIOS 1.5 中引入的。
Each POWER6-based system is configured with a VIOS partition.
每个基于POWER6的系统都配置了一个VIOS分区。
Verify the virtual device configuration and status on each VIOS.
检验每个VIOS上的虚拟设备配置和状态。
WWPNs for all FC adapters on all VIOS involved in the migration.
在迁移所涉及的所有VIOS上的所有FC适配器的 WWPN。
Configured on the blade were a VIOS (IVM) and two AIX 6.1 LPARs.
这台刀片服务器上配置了一个VIOS (ivm)和两个AIX 6.1LPAR。
I activated one of the VIOS and waited while it started to boot.
我启动一个VIOS，等待它开始引导。
Make sure VIOS has sufficient CPU, memory, and network bandwidth.
保证VIOS具有足够的CPU、内存和网络带宽。
You can load ISO images on the VIOS command line, or via the GUI.
可以通过VIOS命令行或GUI装载ISO映像。
This is accomplished by installing a VIOS mksysb image using NIM.
安装方法是使用NIM安装VIOSmksysb镜像。
The physical disks must be assigned to both paging VIOS partitions.
这些物理磁盘必须分配给两个分页VIOS分区。
The supported devices differ between AIX and POWERVM VIOS, as well.
受支持设备在AIX和POWERVM VIOS中有所不同。
Paging will normally be provided by the primary paging VIOS partition.
正常情况下，由主分页VIOS分区提供分页功能。
Each VIOS was given a hostname: bvio82 (slot 13) and bvio83 (slot 14).
每个VIOS有一个主机名：bvio82(插槽13)和bvio83(插槽14)。
However, none of the VIOS or AIX systems are accessing it at this time.
不过，此时，VIOS或AIX系统均没有访问它。
Both of my VIOS were configured with an SEA, on the same physical VLAN.
我的两个VIOS都配置了SEA，它们在同一个物理vlan上。
Mobility activity is logged on the LPAR and the source and target VIOS.
转移活动被记录在LPAR以及源和目标VIOS上的日志中。
With my pool defined, I observed its Settings from the IVM and the VIOS.
定义了池之后，我在IVM和VIOS上查看它的设置。
应用推荐