On the basis of the global optimization of data which is used to build up mold, the artificial intelligent grey theory mold was established to forecast the freeze pressure development trend.
在用遗传方法对灰色理论建模数据进行全局优化的基础上，建立了预测冻结法施工中外层井壁承受冻结压力发展趋势的智能灰色理论模型。
The leftover parts from the mold-the plastic that fills the channels that take the hot plastic into the piece negative-fall down the machine, gets ground up, and put back into the production cycle.
塑料热成型之后的残余物会自机器上掉落下来，被碾碎，并重新进入生产循环过程中。
Seen here is an up-close shot of the mold used to make a three-stud LEGO brick.
现在你所看到的是一个近距离拍摄的用于制造3螺栓的乐高零件的模具。
Nobody wants to watch your science projects blossom mold or begin to stink up the communal space.
没有人想看着你的科研项目绽放“霉菌”，也没人想看到它们把整个公共空间搞得臭气熏天。
For high production runs, a metal mold skin can be most economical, but at a higher up-front cost.
若进行大规模生产，使用金属模具外壳可能是最经济的，但是初始投入成本较高。
I had some flat plate end caps welded up to use as legs and mold material blockages.
我有一些平板端盖焊接起来用腿和模具材料的淤塞。
Short cycle times can be achieved by detaching the mold plates before the concrete is completely set up.
在混凝土完全硬化之前拆模可以缩短周期时间。
A poorly planned or executed mold set-up can resemble a comedy of errors.
模具安排的糟糕计划或行动就像一个错误的闹剧。
Here, the melt cools and hardens until fully set-up. The mold is then opened, the piece ejected, and the sequence repeated.
熔体在模腔里冷却，硬化，直至完全固化。然后将模子打开，推出工件，并重复以上工序。
For the sail I used water based clay and laid up a flat wall that would separate the two sides of the stone mold.
为船帆我用的水为基础的粘土和奠定了一个单位的墙，将单独双方石模具。
Mold is made and I will cast up all of them tomorrow.
模具是和我会投了所有他们的明天。
The design of its molding part was used in the mold, inject system and other make up, and working process of the mould are specified in detail.
详细地叙述了模具成形零件的设计、液压侧抽芯机构、浇注系统和其他结构的设计过程，以及模具工作过程。
And it also makes a further analysis and study on the key technologies of setting up the mold and the digital scanning.
并对其中的关键技术(包括产品建模和数字化扫描技术)作了进一步的分析和研究。
You take a plastic or composite sheet, heat it up, and press it into a mold to make a part.
把一块塑料或复合材料板材加热，压进模具来制作零件的方法。
You've got to pretty much take that chalk, and make a slurry out of it, put water, and dry it back up, put in a mold, and then you can have the chalk again, but you can't just glue it back together.
你得尽可能地收集它的碎片，把它做成粉浆，加水然后风干，放进模具，然后你就能重新得到这支粉笔，但是你不能简单地把它粘起来。
Up to about 14 psi of atmospheric pressure, the necessary pressure is achieved by vacating the space between the sheet and the mold in order to take advantage of this atmospheric pressure.
高达约14磅的气压，必要的压力是通过腾出空间之间的资产负债表摘要及模具，以充分利用这一大气压力。
To implement new processes, drawing up the product documents and for mold technical specifications, assigning suppliers, implementing them in the factory and correcting non-conformities.
导入新工艺，建立产品文件和模具参数，指派供应商，纠正异常情况。
An integration system is set up to meet the need for information integration in the process of mold design and manufacture and detection of aero-engine turbo blade by investment casting.
为满足航空发动机涡轮叶片精铸模具设计、制造、叶片铸件检测流程对信息集成的需求，提出构建精铸模具集成设计系统平台。
Too much water reduces the adhesion and too little piles the material up too thick on the mold surface .
水太多会减少粘附力，加水太少则会使脱模剂在模具表面堆积太厚。
Another possible cause for odor is the build up of slime, mold, hair, etc in the tailpiece (the portion of pipe that comes out the bottom of your sink) or overflow of your sink.
另一个可能的原因是，建立气味煤泥、塑造、毛发、在尾翼等(部分管出来的底层你下沉)或溢流贵沉。
The system makes up for the weakness of CADDS5 used in injection mold structure design. It makes injection mold CAD have come true.
该系统弥补了CADDS5软件在用于注塑模设计中的不足，使注塑模具CAD得以真正实现。
With a product line of tens of categories, we can offer quick copying with precise contraction ratio (up to two thousandth) for mold making.
公司产品品种达几十种，为你的模具制作提供快速的复制，精密的收缩率，产品的收缩率可以达到千分之二。
Proceeded research analyzes for the water environment loading ability the adjusted to control on establish with fluid matter in formation system mode, set up the total frame in mold to the Chinese.
本文就水环境承载能力调控与水质信息系统模式的建立进行了分析研究，并结合中国实情提出了建模总体框架。
The practice proves that the method can be set up as a reference for other complex mold parting design.
实践证明该方法对其它复杂模具分型设计具有参考作用。
Finally take the mold production sets up the virtual enterprise as the case, through the comparison research, has confirmed the method validity and the feasibility which this article proposed.
最后以模具生产企业组建虚拟企业为案例，通过比较研究，验证了本文所提出方法的有效性和可行性。
Finally take the mold production sets up the virtual enterprise as the case, through the comparison research, has confirmed the method validity and the feasibility which this article proposed.
最后以模具生产企业组建虚拟企业为案例，通过比较研究，验证了本文所提出方法的有效性和可行性。
应用推荐