Test result obtained with triple twisting method is the greatest, then is those obtained with double twisting method and one time back twisting and twisting method (GB 2543-81).
在上述三种退捻加捻法中，三倍退捻加捻法测试转杯纱捻度的测试结果最大，其次是二重法和一次退捻加捻法。
This method has overcome the shortcoming of plane analysis method in the past that cannot consider twisting effect.
该方法克服了以往平面分析方法不能考虑扭转效应的缺点。
The geometric relevance to deformation of the twisted fiber bundle was analyzed and the influence of twisting on performance parameters of the bundle was revealed by energy method.
分析了加捻纤维束的变形几何关系，利用能量法揭示了加捻对纤维束性能参数的影响。
Analysis is done to the key part in straight twisting machine, the twister, and a dynamic equilibrium precision is reckoned with a method of repair in application.
深入剖析了先进直捻机的关键部件———匀捻器，并对其动平衡精度进行了推算，提出了应用过程中故障修复的解决办法。
The effect of YGLDG on relieving pain was tested by counting body twisting induced by glacial acetic acid and measuring the latent period of licking hind foot with the hot plate method in mice.
结果：养肝利胆颗粒能明显抑制小鼠耳肿胀度和大鼠足跖肿胀，可对抗醋酸致小鼠扭体反应，提高小鼠对热的痛阈值，可缓解乙酰胆碱致离体胆囊痉挛作用。
The principle and design method of the programmable logic controller (PLC) are introduced in brief. The design strategy of the PLC-based electric control system for ENN 2mn twisting machine is stated.
首先简要地说明了可编程序控制器(plc)的原理及其设计方法，然后提出了采用PLC的ENN2MN扭拧机电气控制系统的设计方案。
In Section 1, we can get twisting modules by the method of twisting which is used in modules.
本文第一部分主要把扭曲的方法运用到模上，从而得到扭曲模。
Methods Mouse twisting body method was used to observe the analgesia effect of essential oil.
方法采用小鼠扭体法，观察当归精油对醋酸所致小鼠疼痛及雌性小鼠痛经模型的影响；
A principle and method are presented which are applied to measure twisting moment and rotation velocity with the help of microcomputer.
论述了一种微机测量扭矩和转速的原理和方法。
Method: The increment percentage of analgesic threshold and analgesia percentage were observed by hot plate test and body twisting test.
方法：运用热板法与扭体法，观察小鼠痛阈提高百分率与镇痛百分率。
In this paper, a compressing twisting-forging-method, based on the yield criterion, is given. It can be used for forging cylinders. The experiments are made with plasticine.
本文以金属塑性成形的屈服准则为依据，提出了一种圆柱体压缩-扭转复合变形工艺，并且用塑性泥做了模拟实验。
In this paper, a compressing twisting-forging-method, based on the yield criterion, is given. It can be used for forging cylinders. The experiments are made with plasticine.
本文以金属塑性成形的屈服准则为依据，提出了一种圆柱体压缩-扭转复合变形工艺，并且用塑性泥做了模拟实验。
应用推荐