The analysis provides valuable reference to transformer design optimization.
分析结果可为变压器的设计优化提供参考。
Deep switch mode power supply design knowledge, e. g. transformer design, topology selection.
较深的开关电源的设计知识，如变压器设计，拓扑选择。
Then transformer design is completed after the adjustment of parameters gotten by initial optimal design.
在此基础上对初步优化后的变压器参数进行调整，完成设计。
Even more frustrating was that it appeared that the root cause was saturation of the new transformer design!
更失望的，失败的根本原因是新变压器设计的饱和。
The new transformer design used an ungapped pot core that was less costly and easier to obtain than a gapped pot core.
新变压器设计采用无缺口的壶型核，其价格低且比有缺口的壶型核供货容易。
How to research stray losses and temperature rise on metal parts caused by leakage flux is difficult task for transformer design.
如何研究由于漏磁引起的附加损耗以及在金属构件中的温升是变压器设计的难题。
The method to fulfil relation between 3-dimension object and non-projection drawing in 3-dimension transformer design system is introduced.
介绍了在变压器三维设计系统中将三维实体与非投影视图实现属性关联的方法。
As for the main part of switching power, in particular, more detail in the transformer design, PWM controller selection, and working theory.
对于开关补偿电源的主电路部分，特别是变压器设计、PWM控制芯片选择、以及工作原理进行了详细的阐述。
For the circumfluence, the experiment results partially match the expectable results, which gives some references for HTS air - core pulse transformer design.
由于环流的影响，实验结果部分与期望值相符，对高温超导空心脉冲变压器的设计具有一定参考意义。
The main contents are made up of the following: common-mode transformer design, hardware design, FPGA function design, and the configuration and debugging of FPGA.
本文的主要内容有：共模变压器的设计，硬件电路的设计，FPGA功能设计，以及FPGA的配置和调试。
Based on analysis and calculation of a transformer, the main points of improvement on the transformer design are described. And some technical problems to be solved are given.
通过对一台实例产品的分析计算，阐述了产品改进设计的要点，并提出了今后需进一步研究解决的技术问题。
How to ensure compliance with the measured value transformer impedance requirements of users and to ensure basic balance is the key to the three-phase impedance of the transformer design.
如何确保符合用户的测定值变压器阻抗要求，以确保基本平衡的关键是变压器设计的三相阻抗。
The formulation design, processing characteristic and material choice of winding without filling in epoxy resin cast dry-type transformer are introduced. The warnings in cast process are presented.
介绍了环氧树脂浇注干式变压器无填料绕组浇注的工艺特点、材料的选择和配方设计，提出了浇注过程中应注意的事项。
Conclusions drew in this thesis can be used to guide the design of on-line monitoring system, some of which, tested by on-site data, can be directly applied in on-line PD monitoring of transformer.
本文所取得的结论对变压器局部放电在线监测系统的设计具有一定的指导意义，其中一些方法经实测数据的验证，可直接用于局部放电在线监测。
Optimization mathematical model of special transformer electromagnetism parameters is a nonlinear programming problem with equality and inequality constraints, to meet some certain design objective.
特种变压器电磁参数的优化设计是一个带有等式和不等式约束，满足某种设计目标的非线性规划问题。
In order to improve the general performance of dry-type power transformer and to shorten new product development period, computing aided design should be further studied and applied.
为了进一步提高干式电力变压器的总体性能，缩短新产品的开发周期，有必要对其计算机辅助设计进行更深入的研究。
Design of virtual calibrator for instrument transformer.
一种虚拟互感器校验仪的设计。
The design of flyback switching transformer and feedback control loop and the improvement of the circuit for considering electromagnetic compatibility are the critical technologies.
反激式开关变压器和反馈控制回路设计，以及考虑电磁兼容性对电路的改进，是其关键技术。
The tank structure of mining flameproof transformer is analyzed by the three-dimensional finite element method. The optimal design of tank has been carried out.
采用三维有限元法对矿用隔爆型变压器箱体结构进行了分析，完成了箱体结构的优化设计。
To achieve high oscillation peaks, the design of the transformer has to be set to high reflected voltage.
要达到比较高的振荡电压峰值，变压器的反射电压必须设置的比较高。
Feature and operation principle of regulation transformer with multi-magnetic circuit. Its design and property are discussed. The self-contained voltage regulation system is introduced.
论述了多磁路调压变压器的特征与工作原理，探讨了其结构与性能，并对与之配套的调压系统做了介绍。
The theoretical basis is provided for the design of power transformer.
为电力变压器的设计提供理论依据。
Design and test of optical voltage transformer.
光学电压互感器的设计和试验。
The study provides a new heat design method for developing high ignition point oil transformer.
这为高燃点油变压器的研制开发提供了一种热设计的新方法。
The article introduces the critical technical parameters, structure and design features of this main transformer and smoothing reactor.
本文介绍了这种主变压器和平波电抗器的主要技术参数、结构和设计特点。
In addition, the company also according to customer design, manufacture special specifications for the transformer.
另外，我公司还可根据客户要求设计，制造特殊规格用途的互感器。
It introduces the working theory of AC manostat of compensated transformer mode, the design of the hardware circuit and the function of the software.
介绍了补偿变压器方式的交流稳压器的工作原理、硬件电路的设计和软件的功能。
From the angel of minimizing the inverse transformer capacity, a method to design inverse transformer capacity based on the technical features of mine-well hoist was given.
通过从如何减小逆变器的装置容量入手，根据矿井提升机的工艺特点，给出了斩波串级调速系统逆变变压器容量的设计方法。
This paper USES the method in the study of power transformer optimum design. The method to select the control parameters of the algorithm is introduced in detail.
将遗传退火算法用于电力变压器优化设计问题的研究，介绍了算法实现过程中各种参数的选择方法并给出了具体算例。
This paper USES the method in the study of power transformer optimum design. The method to select the control parameters of the algorithm is introduced in detail.
将遗传退火算法用于电力变压器优化设计问题的研究，介绍了算法实现过程中各种参数的选择方法并给出了具体算例。
应用推荐