Fees for Chromatic Harmonica Solo (Open Section) and Tremolo Harmonica Solo (Open Section) include the cost of one copy of the test piece.
半音阶口琴独奏公开组及复音口琴独奏公开组之报名费已包括指定乐曲乐谱一份之费用。
If tack welds are to be fused into the final joint they shall be included in the test piece.
如果临时点焊熔入最终的焊缝，它们应包括在试件内。
As a result, the effects of geometric size of test piece on J-R curve un-der different degree of constraint are argued.
从而论证了不同约束条件下，试样的几何尺寸因素对其J阻力曲线变化趋势的影响规律。
The additional test specimens can be taken from the same test piece if there is sufficient material or from a new test piece.
附加试样可从同一个试件上切取(如果有足够材料的话)或从一个新试件上切取。
When impact requirements apply, the upper limit of heat input qualified is 25 % greater than that used in welding the test piece.
当采用冲击要求时，适合的热输入的上限比试件焊接时使用的热输入大25%。
After reaching the temperature of the furnace, maintain the test piece at that temperature for not less than 10 min.
达到熔炉的温度后，将测试条保持放在熔炉里至少10分钟。
When hardness requirements apply, the lower limit of heat input qualified is 25 % lower than that used in welding the test piece.
当采用硬度要求时，适合的热输入的下限比试件焊接时使用的热输入低25%。
The utility model relates to a liquid test piece for measuring liquid, which comprises a base plate, an interlayer, and a top head piece.
本实用新型一种液体检测试片，用于液体量测，其包含一基板、一中 间层、一上盖片。
This test piece shall be welded using the identical welding parameters as the original test and only weld metal impact test specimens shall be tested.
此试件应使用与原始试验相同的焊接参数进行焊接，并且仅对焊接金属冲击试样进行试验。
By observing and analyzing the casting test piece, we have found a metallurgical integrating layer that is made up of chromizing cast-iron alloy layer.
我们还对铸渗质量较好的铸渗试件进行了观察和分析，发现铸铁渗铬合金层与母材结合良好，呈冶金结合。
This paper believes that the calculating formula of moment of inertia for bow-shaped test piece in GB/T 13096. 2-91 is wrong because of printing error.
本文认为GB/T 13096.2-91中计算弓形试样截面惯性矩的公式有误，同时指出在某些手册中有关计算公式也有误。
Structure of the mount model is modified, and stiffness measurement and fatigue durability test were made to the test piece before and after the modification.
对悬置模型进行结构改进，并对改进前、后的试件进行了刚度测量试验和疲劳寿命试验。
According to the standard's requirements, test piece for qualification of welding procedure and for product welding should be carried out various bending test.
焊接工艺评定试板和产品焊接试板，按标准要求都要进行弯曲试验。
The casting concrete test piece is used to carry out blasting experiment under laboratory conditions, and then calculations are conducted using fore-mentioned approaches.
在实验室条件下采用浇注的混凝土试件代替岩石进行爆破实验，然后应用提出的方法进行了分维数计算。
Using traditional interferometric method, as the germanium material is too soft to process, the surface form of the test piece may not meet the requirement for the measurement.
运用传统的干涉法检验光学材料的折射率均匀性时，由于锗晶体太软，表面不易加工，其表面面形难以满足测试要求。
A field investigation of corrosion status of buried pipeline and measurement of the soil parameters were conducted, accompanied with corrosion test piece laying and field sampling.
进行了现场腐蚀状况调研，对现场埋地管道的土壤腐蚀情况就地测量了相关参数，并进行了腐蚀试片埋设和现场取样工作。
The nitriding process comprises the following steps: cleaning the test piece again with the gasoline or acetone, or blowing sands on the test piece with low wind pressure fine sands;
氮化处理工艺是将试件再次用汽油或丙酮清洗干净，或用低风压细沙进行吹沙；
It was shown by experimental results that the technique was effective for rapid and intuitive testing of the bonding quality and structure of an aluminum honeycomb composite test piece.
用红外热波技术对铝蜂窝夹层胶接结构进行检测，结果表明，该技术可对试件夹层胶接质量和蜂窝结构作快速有效直观的检测。
If the test piece fails to comply with any of the requirements for visual examination or NDT specified in 7.5, one further test piece shall be welded and subjected to the same examination.
如果试件不符合7.5规定的外观检查或非破坏性检查的要求，应再取一个试件进行焊接，并进行同样检查。
Through the microstructure analysis and residual stress measurement on a quenching test-piece, the feasibility of the numerical simulation is proved.
通过对淬火试件进行金相组织分析和残余应力测量，验证了数值模拟的可行性。
Thus continuing the regular measurements of the bending curves of the test-piece, one could construct a creep curve.
如此继续进行试件的挠度观测，就可绘制出蠕变曲线。
A bending of the test-piece should be reduced to a difference between the profile at the measurement and the initial profile which was determined before bending.
试件的挠度应减小到观测时的轮廓与弯曲前已确定了的初始轮廓之间的差值。
There is a fixed relationship between the gauge length and the cross-sectional area of the test-piece at the reduced diameter.
标距长度和试样在直径减少处的横截面面积之间有固定的关系。
There is a fixed relationship between the gauge length and the cross-sectional area of the test-piece at the reduced diameter.
标距长度和试样在直径减少处的横截面面积之间有固定的关系。
应用推荐