The series method of stress strength model is used to evaluate structural reliability.
可靠性评估方法是基于应力—强度模型的串联法。
Fatigue strength is less than static stress strength such as elasticity limit, yield strength.
疲劳强度低于弹性极限或屈服强度等静应力强度。
And then, by using the stress strength interference theory to calculate fracture probability is converted to resolve a one dimensional integral.
当用应力—强度干涉理论计算断裂概率,问题归结为一维积分式的求解。
The analysis result shows that the stress strength in the support locations of the stirred reactor is enough, and can satisfy safety requirements.
分析结果表明,该反应器支座区域的强度足够,可满足安全要求。
Since the pressure gradient affects stress strength of crack top, it is unsuitable to judge crack initiation by the traditional breakdown pressure.
气体压力分布影响裂缝尖端应力强度,因而不能用传统的破裂压力来判断裂缝起裂扩展。
A computation program has been developed, using a two dimension boundary element method, for calculation of stress strength factor at the welding crackle tip.
反映裂纹尖端附近区域应力场强度的物理量称为应力强度因子。它和裂纹大小、形状以及外应力有关。
Mesoscopic damage size on the top of crack is analysed, the effective stress strength factor is defined, the mode I crack damage fracture criteria is presented.
以混凝土单轴拉压损伤为基础,给出了单元弹性损伤本构关系,分析了裂纹尖端损伤微裂区尺寸,定义了有效应力强度因子,给出了I型裂纹损伤断裂判据。
The monotone property of multivariate function proved that the maximum stress strength point exists on the inner surface of casing under the triaxial stress conditions.
通过实例计算,对比分析了用“三向应力圆”理论与其他几种理论计算的抗挤强度值。
Using the LFEM theory, the author provided the computing method of stress strength factor of crack and the criteria of crack instability propagation and propagation angle.
本文根据砂岩储层的物理力学特征,运用断裂力学理论,给出了储层裂缝的应力强度因子的计算方法,定量地分析了开发过程中储层裂缝失稳扩展的判据、裂纹扩展方向。
According to the maximum stress strength criterion, the burst pressure formula for the single spiral and the spiral with hoop filament-wound toroidal pressure vessel were obtained.
利用最大应力强度准则,得到了单一螺旋缠绕及螺旋加环向缠绕圆环压力容器爆破压强的计算式。
Based the numerical simulation for sphere tank with defects, fracture safety assessment and stress strength verification are done under the cases of working pressure and over pressure.
在数值模拟计算含缺陷球罐应力场的基础上,对含缺陷球罐在工作压力和超压两种工况下进行了断裂安全评定和强度校核。
If probability density functions of stress and strength are definite, stress strength interference model can be used to calculate reliability using formulation or numerical value integration.
应力、强度概率密度函数确定可采用应力-强度干涉模型,用公式或数值积分求可靠度。
The stress, strength and other design variables of porcelain sleeve can all be considered to obey normal distribution, and dealt as normally distributed variables during calculation.
瓷套的应力、强度和各设计变量均可认为服从正态分布,在设计时作为正态分布变量处理。
The viewpoint that the interference area of the stress - strength interference model in reliability design is the probability of failure is discussed in this paper.
本文对可靠性设计中应力—强度干涉模型的干涉面积就是失效概率的观点,提出商榷。
Perform mechanical stress, strength, and deformation calculation.
执行机械应力,强度和变形计算。
Impact stress and impact strain are solved by energy method. Stress - strength interference model can be used to impact investigation. Reliability design of impact has been studied.
用能量法求冲击应力和冲击变形。并将应力强度干涉模型运用于冲击问题,讨论了冲击的可靠性设计。
Reliability of a static stress-strength system depends only upon the interference of stress and strength.
静态应力-强度系统的可靠度仅与应力和强度的干涉有关。
Since the main failure reason of the steel rope is the fatigue of the metal, the fatigue reliability design of the crane steel rope can be executed by means of stress-strength interference model.
根据起重机钢丝绳失效主要是金属疲劳的原理,采用应力-强度干涉模型,对起重机钢丝绳进行了疲劳可靠性设计。
This model capitalizes on stress-strength interference theory and curve, and Weibull model about the winds distribution is considered.
该模型利用应力-强度干涉理论,并且假定风速服从威布尔分布。
The statistical damage mechanical essence of the stress-strength ratio criterion is discovered on the base of the data from a SW deep lying tunnel.
进而提出采用平行杆模型模拟洞室围岩,以西南某深埋隧洞为例,推出了岩爆应力强度比判据分界点的统计损伤意义。
The statistical damage mechanical essence of the stress-strength ratio criterion is discovered on the base of the data from a SW deep lying tunnel.
进而提出采用平行杆模型模拟洞室围岩,以西南某深埋隧洞为例,推出了岩爆应力强度比判据分界点的统计损伤意义。
应用推荐