Now, we will start the application.
现在，我们将会启动应用程序。
Click Run to start the application.
单击Run启动应用程序。
When recording, start the application.
记录时，启用这个应用软件。
Save your changes and start the application.
保存您的更改，并启动应用程序。
Type grails run-app to start the application.
输入grailsrun-app启动应用程序。
You can now start the application server program.
现在，您可以启动应用服务器程序了。
From here you can stop and then start the application server.
在这里可以停止并启动应用服务器。
This information is of use to know how to start the application.
该信息可用于了解如何启动应用程序。
You can start the application with minimal resources and at a low cost.
开始时，可以用少量的资源以较低的开销先启动这个应用程序。
Click on the ParsingXML application to start the application activity.
单击ParsingXML应用程序启动应用程序活动。
If you install using the administrative console, start the application.
如果使用管理控制台进行安装，则启动该应用程序。
Save these changes to the master configuration and remember to start the application.
将这些更改保存到主配置中，并记得启动应用程序。
Finally, the Server must be started so it is ready to install and start the application.
最后，必须启动服务器，准备好安装和启动应用程序。
Start app after install: Check box to start the application immediately after deployment.
Startapp afterinstall：用于在部署后立即启动应用程序的复选框。
Because of special startup procedures, triggering cannot be used to start the application server.
由于特殊的启动流程，触发机制不能用于启动该应用程序服务器。
Open 'Programs' from the start-menu on the Pocket PC and select FinchSync to start the application
从开始菜单中选择“程序”，然后点击FinchSync启动程序。
When you start the application for the first time, there will be no processes, and hence, no tasks to work on.
在第一次启动应用程序时，还没有流程，因此没有要执行的任务。
It is not enough to just start the application after it has been installed because the message bus will not start.
在应用程序安装后只启动它是不够的，因为消息总线还未启动。
You can then start the application server by choosing the start button available when you right click on the server.
然后启动应用服务器，方法是右键单击服务器时选择Start按钮。
Select the check box in the Select column for the CallForwardingSample.sar file, and click Start to start the application.
为CallForwardingSample.sar文件选中Select列的复选框，并点击Start以启动应用程序。
To actually run the demo application, it's worth noting that the only thing you should have to do is to start the application.
要真正地运行演示应用程序，惟一要做的就是启动该应用程序，这一点值得注意。
Users can then select a specific look and feel by using the following syntax in the command line when they start the application.
当用户启动应用程序时，他们可以通过在命令行中使用以下语法来选择一个特定的lookandfeel。
Once all changes have been made on the cluster members, stop and start the application servers using the WebSphere administration console.
在集群成员上完成了所有的更改后，使用WebSphere管理控制台停止后再启动应用服务器。
The main() method creates an instance of the AppStarter class and passes it to the SwingUtilities.invokeLater() method to properly start the application.
main()方法创建一个AppStarter类实例，并将它传递给 SwingUtilities.invokeLater() 方法，来正确启动应用程序。
In order for the WebSphere Personalization run time to pick up this new class, you must stop and start the application server in the WebSphere administrator's console.
为使WebSpherePersonalization运行时检取这个新的类，您必须在WebSphere管理员的控制台中停止并重新启动应用程序服务器。
Once you've completed the steps above, start the application Server, then deploy and start the JMS J2EE application from the administration console to verify the application.
完成了上述步骤后，启动ApplicationServer，然后在管理控制台部署并启动JMSJ2EE应用程序，以便对其进行验证。
Now start the application in the test environment, and you will notice that all requests to the Supplier service are now routed through the tcpmon tool, as shown in Figure 10.
现在，请在测试环境中启动该应用程序，您将注意到所有发向供应商服务的请求现在通过tcpmon工具来路由，如图 10所示。
启动应用程序服务。
Start the application normally.
正常地启动应用程序。
Start the application servers.
启动应用程序服务器。
应用推荐