Figure 2 shows a standard START command.
图2显示了一个标准的START命令。
How to use the start command in a batch file?
如何使用批处理文件中启动命令？
The roo-hindi-addon was started using osgi start command.
roo - hindi -addon通过osgistart命令启动。
To start heartbeat, issue a service heartbeat start command.
要启动heartbeat，发出一个service heartbeatstart命令。
Create two additional DOS consoles by typing the start command.
通过键入start命令，创建两个额外的DOS控制台。
In this case, it is the default START command of an application server.
在本例中，它是应用服务器的缺省START命令。
Modify the Xdmx start command to include the third node, as in Listing 5.
然后修改Xdmx的启动命令，包含第三个节点，如清单5所示。
To start any of the services, use the start command (for example, start 8).
要启动任何一个服务，应使用start命令(例如，start8)。
Note that only the control region start command is needed to start a server.
请注意，启动服务器只需要控制区域START命令。
If the number of seconds is not specified, the Start command waits indefinitely.
如果未指定秒数，则“启动”命令将无限期等待。
Now start the Tomcat Web server by providing the catalina start command under the CATALINA_HOME \ bin folder.
现在通过在CATALINA_HOME \bin文件夹下提供catalinastart命令来启动TomcatWeb服务器。
The rsync daemon is enabled using the rsyncd-enable shell script and then started using the rsyncd-start command.
rsyn守护程序可用rsyncd -enableshell脚本启用，然后再用rsyncd - start命令实际启动。
If you want to start the Jazz build server later on again on your machine copy the provided start command or use the commands provided below.
如果稍后希望再次在本地计算机上启动Jazz构建服务器，可以复制所提供的启动命令，或者使用下面提供的命令。
This command sets the classpath to point to the Infocenter JAR file, tells it where Eclipse is installed, sets the port number, and issues the start command.
此命令将classpath设置为指向InfocenterJAR文件，通知该文件eclipse安装的位置，设置端口号并发出start命令。
Listing 7 shows the use of the geronimo.sh start command to start WebSphere Application Server Community Edition as well as the use of the gsh.sh command to wait on startup.
清单7显示了使用geronimo . sh start命令启动WebSphereApplicationServerCommunityEdition，以及使用gsh. sh命令等待启动。
Figure 13 shows the sample output from the start node command.
图13显示了启动节点的命令的示例输出。
Simply set the environment variable at the start of the command line and the command you want to run.
只需要在启动命令行的时候设置环境变量以及您希望运行的命令即可。
However, that's just the start of the command.
不过，这只是命令的开头。
Connect to the standby database and start HADR on the standby server by executing the start HADR command.
连接备用数据库，执行STARTHADR命令在备用服务器上启动HADR。
Connect to the primary database and start HADR on the primary server with the start HADR command.
连接主数据库，执行STARTHADR命令在主服务器上启动HADR。
You can use the following command to start yamd.
您可以使用下面的命令来启动yamd。
To start it, run the command STRMQBRK.
要启动代理，运行命令strmqbrk。
Start the tcpdump command in the server as follows.
在服务器上启动tcpdump命令。
The following command will start the OnDemand instance.
下述命令将启动OnDemand实例。
Create a queue manager using the CRTMQM command and then start it using the STRRMQM command.
使用crtmqm命令创建一个队列管理器，然后使用strrmqm命令启动它。
Start wsadmin from the command line by entering.
通过输入以下命令从命令行启动wsadmin。
To explore the awk command more fully, start with the command man awk in addition to the resources mentioned in the Resources.
若要更完整地学习awk命令，请从命令man awk开始，并参阅参考资料部分提供的资源。
On the primary machine, first activate the database and then issue the start hadr command to start it as the primary database (Listing 8).
在主要计算机上，首先激活数据库，然后发出starthadr命令将其作为主要数据库启动(清单8)。
On the standby machine, first deactivate the database and then issue the start hadr command to start it as the standby database (Listing 7).
在备用计算机上，首先禁用数据库，然后发出starthadr命令，将其作为备用数据库启动(清单7)。
The nohup command is used to start a command that will ignore hangup signals and will append stdout and stderr to a file.
nohup命令用于启动一个忽略hangup信号的命令，并且将stdout和stderr附加到文件。
应用推荐