Some matters needing attention on selection of the scale and the size of drawing sheets in CAD for chemical equipment were presented in this paper.
针对化工设备CAD中的比例和图幅选择，故提出应注意的几个问题。
You define the fixed size of the canvas in the element itself, and then typically you do the actual drawing from a script that uses the canvas API to create visual objects on the canvas.
首先在元素本身中定义画布的固定大小，然后利用使用 canvasAPI 在画布上创建可视化对象的脚本来实际绘画。
An added benefit to the vector nature of Cairo drawing is that vector images tend to be smaller in size.
cairo采用矢量绘图还有一个优点：矢量图像往往比较小。
Through various drawing methods and annealing steps, We produces different physical characteristics in wire of a given size.
通过各种绘图方法和退火步骤，我们产生不同的物理特性，在一个给定大小的丝。
Note that drawing off screen (outside of the bounds defined by size) is not illegal, but simply ignored.
请注意，超出屏幕边界(size定义的边界外)画线并非不允许，只是被忽略了而已。
Pull out of the wire, precise size, smooth surface, and the use of drawing equipment and mold is simple, easy to manufacture.
拉出的丝，尺寸精确，表面光洁，且所用拉拔设备和模具简单，制造容易。
Describes the principle and method of size driving AUTOCAD drawing in AUTOLISP and gives an example in detail.
介绍了用AUTOLISP语言实现在AUTOCAD中尺寸驱动修改图形的原理及方法，给出了具体实例。
In this paper, Based on a detailed analysis of existing regional space law it give a drawing applied to the irregular method of calculating the size of the region.
本文在详细分析了现有区域面积计算法的基础上，提出了一种应用于图纸上不规则区域的面积计算方法。
Two kinds of size effects on micro deep drawing are investigated, which can be explained by surface layer model and strain gradient model.
另一个为考虑应变梯度效应的模型，该模型在已有的材料特征基础上引入了尺度效应。
In this paper calculation method of complex drawing piece on unfold size is given.
本文提出了复杂拉深件展开尺寸的计算方法。
Line location: according to the installation location, size and elevation in the drawing out of doors and Windows, doors and Windows on both sides of the doors and Windows to the edge line.
划线定位：根据设计图纸中门窗的安装位置、尺寸和标高，依据门窗中线向两边量出门窗边线。
The forming characteristics of different size drawing parts were also described.
描述了用不同尺寸的毛坯拉伸零件时的变形特点。
This is commonly used by MIP mapping where the displayed image size determines the resolution of the image used for drawing.
这通常由mip映射使用，其中显示的图像大小将决定用于绘制的图像分辨率。
If other errors can't be detected, double check whether the size of work piece program can completely match with the size of original drawing.
如果没有检测出其它误差，重新仔细检查工件程序的尺寸是否与原来的图纸的尺寸完全匹配。
Through computing the size of the roughcast and the number of drawing are confirmed. Finally analyzed the craft to the hinge and confirmed the craft project.
通过计算确定了杯座毛坯尺寸及拉深的次数，通过对工件工艺性分析，确定了工件的工艺方案。
This paper states the basic principle of operation of cold drawing and straightening machine. It derives basic formula to determine the major size and parameters.
说明了该冷拉调直机的基本工作原理，推导了确定关键尺寸参数的基本公式。
The results showed that, there is a deformation tendency of drawing, and flanging and the tendency is related to, in the same parameter of die and the same technological conditions, the hole size.
试验所获应变分布表明，带孔件在变形过程中存在拉深和翻边两种变形趋向性，在模具参数和工艺条件完全相同的情况下，其可能的变形趋势与孔的尺寸有关。
Size of the machine can be consulted the drawing.
机器安装尺寸可参阅图。
As free drawing on the flat anvil, the size of feed plays the very important role to its drawing efficiency.
平砧上自由锻拔长，送进量的大小对其拔长效率起着至关重要的作用。
Returns the value of the specified size property of the current visual style part using the specified drawing bounds.
使用指定所绘制界限，传回目前视觉化样式组件之指定的大小属性值。
The large diameter mesophase pitch carbon monofiber in uniform size was obtained by controlling the matching of extrusion flow and drawing rate.
熔纺时控制了挤出流量和牵伸速率的良好匹配，获得了丝径均匀的大直径中间相沥青炭单丝。
Introduced design of the adjustable blanking-drawing compound for the drawing with flange, the drawing die could adjust the flange size, and satisfied the part tolerance requirement.
介绍了带凸缘拉伸件可调式落料拉伸复合模设计，实现对凸缘直径尺寸可以进行调整以实现一定公差要求的模具结构。
The similar problem on computing blank size also exists in sheet forming, such as spreading size of bending piece, blank size of axial symmetry parts by deep drawing.
板材成形中同样存在着计算坯料尺寸的问题，如弯曲件展开尺寸的计算，轴对称拉深件坯料尺寸的确定等。
You may need to extend long pipelines beyond the boundaries of a standard-size drawing page.
您可能需要将长管道延长到标准绘图页的边界外。
The results showed that the metallurgical defects such as inclusions, coarse crystal grains and asymmetry of the grain size were the main reason resulting in fracture of the steel rods during drawing.
结果表明，原材料中存在的夹杂物、晶粒粗大及混晶等冶金质量缺陷是盘条在拉拔过程中发生断裂的主要原因。
In the drawing module of graph, geometric figure of simulated domain, thermal circulation curve and selection probability of each site and grain size distribution are visual.
在图形显示模块中，实现了模拟区域几何形状、格点热循环曲线、格点选择概率及晶粒尺寸分布的可视化。
For the dimensions of the double extention worm shafts, please consider the drawing of relevant NMRV size.
所有双出轴蜗杆的尺寸，请参考NMRV的相关图纸。
In this paper, the causes of size migration and its effects on chopped strand MATS are analyzed from aspects of raw material selection, fiber drawing process and fiber drying process.
本文从浸润剂原材料的选择、拉丝工艺和烘干工艺三方面分析了浸润剂迁移现象产生的原因及其对短切毡的影响。
In this paper, the causes of size migration and its effects on chopped strand MATS are analyzed from aspects of raw material selection, fiber drawing process and fiber drying process.
本文从浸润剂原材料的选择、拉丝工艺和烘干工艺三方面分析了浸润剂迁移现象产生的原因及其对短切毡的影响。
应用推荐