I made a simple brass servo mount that's bolted to the end cap.
我提出一个简单的黄铜伺服山认为的螺栓到去年底的上限。
The card can collect four axes' encoder pulse signals simultaneously, and control servo motor by four output analog voltage. Furthermore, it can control input and output I/O signals.
该运动控制卡能同时采集四轴的编码器脉冲信号，输出四路模拟电压控制伺服电机，同时能控制I/O信号的输入和输出。
For inspecting the validity of simulative load system, I have connected with the servo system and simulative load system and done many experiments on these systems.
将数字伺服系统与模拟加载系统对接，进行了大量的加载实验以验证模拟负载系统的有效性。
This paper puts forward a new MRACS method using low order model, i. e. the fourth order hydraulic servo system following the first order reference model.
本文把液压伺服系统作四阶系统，跟随一阶参考模型，提出了一种新的高阶对象和低阶模型的MRACS 的方法。
I bore down hard on the fact my shop boss was servo trained and held my breath for fear I'd be asked how many men I had.
我强调我的工场管理人在塞尔伏受过训练的事实，可是我又紧张得恐怕有人问我到底有多少工人。
Currently, the design of shaking table control system is based on two assumptions, i. e. linear servo valve, and rigid table and payloads.
振动台控制系统设计时对物理系统进行了两个基本假设：伺服阀线性、台面和负载刚性。
To verify the theoretical results of dynamic walking and satisfy the economy requirements, this paper designs and implements a planar footless biped robot THR-I based on bus servo motor.
为了既能验证动态步行的理论结果，又能满足经济性的要求，本文设计并实现了一种基于总线型伺服电机的平面无脚双足机器人THR-I。
Now, you would see I-SAC controller will be the only choice if you want to design a very high performance servo corollary.
现在，你会看到我，国资委控制器将是唯一的选择，如果你想设计一个高性能的伺服的必然结果。
Shortened settling time by I-SAC controller and realized utmost performance that was impossible by conventional servo controllers due to their poor versatility.
缩短了我，国资委控制器，实现了由传统的伺服控制器由于其通用性差最大的性能，是不可能解决的时间。
I-SAC servo controller is the one that completely surpasses conventional classical control theory represented by PID.
一至国资委伺服控制器是一个完全超越了传统的经典控制理论的PID代表。
If you were trying to describe how a gun-pointing servo mechanism works, you might start out by saying, "Suppose I push down on the gun-barrel to create a position error."
如果你试图去描述火炮瞄准的伺服机制是如何工作的，你可能会这样开头：“假设我把炮管下压产生了一个位差。”
It took over 1 minute for transferring in the conventional system; I-SAC used pneumatic servo system could shorten the time to approx. 15 seconds only.
它接管了1分钟，在传统系统转让的，我的死胡同采用气动伺服系统可以缩短时间approx .15秒只。
The output end of the V-I converting and current amplifying circuit drives a ratio servo valve and controls the actions of a clutch.
与所述信号累加单元的输出端电连接的V-I变换及电流放大电路；
The output end of the V-I converting and current amplifying circuit drives a ratio servo valve and controls the actions of a clutch.
与所述信号累加单元的输出端电连接的V-I变换及电流放大电路；
应用推荐