The mail databases were spread across two IBM EXP arrays (direct connect SCSI), configured as RAID 0 on each server.
邮件数据库分布于两个IBMEXP阵列（直连SCSI），阵列在每个服务器上都配置为RAID0。
方法2：虚拟scsi磁盘。
Two SCSI controllers and two disks
两个SCSI控制器和两个磁盘
Define the virtual SCSI disk maps (VIO).
定义虚拟scsi磁盘映射(VIO)。
The typical SCSI generic driver commands.
典型的SCSI通用驱动器命令。
It also manages SCSI-specific error recovery.
它也负责管理特定于SCSI的错误恢复。
Table 2 shows how the SCSI standard is defined.
表2显示如何定义SCSI标准。
All SCSI commands should also contain a control byte.
并且所有SCSI命令都要包含一个控制字节。
Many drivers use these atomic operations, particularly SCSI.
许多驱动程序使用这些原子操作，特别是SCSI。
The SCSI subsystem is one of these block device drivers.
scsi子系统是这种块设备驱动器之一。
The process of sending the SCSI command here is quite simple.
发送SCSI命令的步骤非常简单。
Status: SCSI status byte as defined by the SCSI standard.
status：由scsi标准定义的SCSI状态字节。
Various controllers, such as IDE and SCSI, are also supported.
支持各种控制器，比如ide和SCSI控制器。
The storage access protocol is the SCSI block command set.
存储访问协议就是SCSI块命令集。
SPC defines behaviors that are common to all SCSI device models.
SPC定义对所有scsi设备模型通用的行为。
Devices like scanners or SCSI adapters use this transfer type.
像扫描仪或者scs i适配器这样的设备使用这种传输类型。
You've created the virtual SCSI devices in the partition's profile.
您已经在该分区的概要中创建了虚拟scsi设备。
In such a case, the SCSI bus will be the performance-limiting factor.
在这种情况下，SCSI总线将成为限制性能的因素。
Listing 2 shows the source code clips of using the SCSI generic API.
清单2显示了使用SCSI通用API的源代码片段。
Internal storage using SCSI adapters and drives dedicated to the partition.
专用于分区的使用SCSI适配器和驱动器的内部存储器。
It USES the standard SCSI command set for interacting with SAS End devices.
它使用标准的SCSI命令集与sas端设备交互。
For example, on one of my test systems it got stuck doing SCSI detection.
例如，我的一个测试系统在检测scsi的时候挂起了。
With these parameters, the SCSI command could be sent to the target device.
有了这些参数之后，就可以将SCSI命令发送到目标设备。
You don't need to waste time trying to track down video drivers or SCSI drivers.
您不必将时间浪费在尝试寻找显卡驱动程序或SCSI驱动程序上。
In Figure 2, you can see how different applications communicate with SCSI devices.
在图2中，您可以看到不同的应用程序如何与SCSI设备通信。
The mid level also provides SCSI command queuing between the upper and lower levels.
中间层还提供了较高层和较低层间的SCSI命令排队。
Virtual storage using a virtual SCSI adapter and storage in a different partition.
使用虚拟scs i适配器的虚拟存储器和不同分区中的存储器。
The storage often acts as a SCSI target that receives and processes SCSI commands.
存储介质通常充当SCSI目标，它接收和处理 SCSI命令。
An inquiry command is the most common SCSI command that all SCSI devices implement.
inquiry命令是所有SCSI设备实现的最常用的SCSI命令。
应用推荐