螺杆与泵体紧密贴合。
When the pump body with a safety valve, overloading security role.
本泵身带有安全阀，超载时起安全作用。
KCB gear pump are mainly gear, shaft, pump body, valve, shaft end seal.
kcb齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。
If the pump is not charged, you are advised to fill the pump body by hand.
如果泵不起诉，建议您以填补泵体的手。
Transparent tube and pump body of material consistent, hardness, have the same life.
透明管和泵体的材料一致，硬度相当，具有同样的寿命。
Sealing ring is fitted on pump body, while impeller sealing ring is an optional part.
设有泵体密封环，而叶轮密封环为可选用件。
The relief valve can be cast and pump body and pump cover, also can separate assembly.
安全阀可以与泵体或泵盖铸成一体，也可以单独装配。
Pump body is by cast iron casting blank forming, severe wear new thing should be changed.
泵体是由铸铁铸造毛坯成型，出现严重磨损时应更换新件。
Marine grade aluminium pump body with Rilsan lining is a proven robust pump design for long life.
海洋级铝泵体与丽绚衬砌是一个强有力的证明，泵的设计寿命长。
This article introduces a series of special clamps for machining pump body of a Shoot Liquid pump.
本文介绍了某种射流泵泵体加工的系列专用夹具。
When need cooling: through a variety of cooling fluid, pump body can maintain a constant temperature.
需冷却时：通过各种冷却液，可以保持泵体的恒温。
Both water inlet and outlet pipelines should be supported by a separate stand and not by the pump body.
进出水管路应另设支架支撑，不得籍泵本体支撑。
The nozzle body extends towards the outside of the pump body to provide a burner with supercharging oil.
所述喷嘴体朝泵体的外部延伸，以便将增压油供至一个燃烧器。
In this paper, abrasion behavior of carbonitriding steels used in the manufacture of pump body is studied.
研究了碳氮共渗钢制作的水泵体的磨损特性。
Therefore, the pump body and screw cylindrical surface and screw and screw clearance should be as small as possible.
因此，泵体与螺杆外圆表面及螺杆与螺杆间隙应尽可能小些。
The results can provide a basis to improve the pump body structure and further improve the pump working reliability.
该文为改善泵体结构，进一步提高深井离心泵的使用可靠性提供了依据。
Precision machining pump body can make "d" type bearings and gear axle, ensure accurate gear axis gear eccentric wear, not to.
精密加工的泵体可使“D”型轴承与齿轮轴精确配合，确保齿轮轴不偏心，以防齿轮磨损。
Jacket and pump body casting into an organic whole, heat preservation effect is good, can avoid welding all kinds of problems.
夹套与泵体铸造成一体，保温效果良好，能够避免焊接夹套产生的各种问题。
The pump body and pump cover composes the pump studio. The inlet of the pump body is horizontally while the outlet is straight-up.
泵体和泵盖构成泵的工作室，泵体的入口为水平方向，出口垂直向上。
Ruled out: relax fill, dredge flume; disassemble pump body to remove debris, rust; Calibration shaft removed or replaced a new shaft.
排除：放松填料，疏通引水槽；拆开泵体清除杂物、除锈；拆下泵轴校正或更换新的泵轴。
The pump comprises mainly of pump body, cover, impeller, shaft, seal ring, intermediate support, sealing and suspension assembly, etc.
泵主要由泵体、泵盖、叶轮、轴、密封环、中间支架、密封和悬架部件等组成。
The complex pump body in the pump is fabricated by that a pump body, a whorl casing, a liquid inlet pipe, and a cover plate are assembled.
泵中复杂泵体由泵体、涡壳、进液管及盖板等部分组装而成。
Non-pollution, The pump body is made of polyvinyl chloride (pvc)plastics, and the onter cover is of cold-rolled steel plate with backing finish.
无污染，本机箱体为聚氯乙稀塑料，外壳采用不锈钢和冷板静电喷塑壳两种。
YCB arc gear pumps are mainly gear, KCG axis, the pump body, cover, the axial bearing, sealing etc. Using double circular-arc gear tooth sine curve.
主要有齿轮、轴、泵体、泵盖、轴承套、轴端密封等组成。齿轮采用双圆弧正弦曲线齿形制造。
The main parts include pump body, pump cover, impeller, axis, sealing rings, intermediate support, sealing and suspension parts and other components.
泵主要由泵体、泵盖、叶轮、轴、密封环、中间支架、密封和悬架部件等组成。
The manufacturing process of foaming mould of an oil pump body by using LOM prototype, electroforming and wire-arc spraying was introduced in detail.
以制造泵体发泡模具为例，详细介绍了在LOM原型的基础上，通过LOM原型的预处理、电铸和电弧喷涂等工艺手段快速制造发泡模具的过程。
In this paper, die structure and design parameters, techno - economic analysis of liquid extrusion for the aluminium alloy oil pump body were introduced.
本文介绍了铝合金油泵壳体液态挤压的模具结构及设计参数、技术经济分析。
Conveyor illiquid, high viscosity of the medium or the transport medium for heating or thermal insulation, choose double screw pump heat pump body structure.
输送流动性差，粘度高的介质或对所输送介质进行加热或保温时，选双层加热泵体结构的螺杆泵。
Pump body seal part of the series for two sets of mechanical seals, mechanical seal, code-named the upper part 60b, the lower mechanical seal, code-named 60a.
泵体部分的轴封为两套串联的机械密封，上部机械密封代号为60b，下部机械密封代号为60a。
Particularly necessary to point out that the liquid in the pump body mass flow rate of less than the circumference of the circumferential speed of the impeller.
需要特别指出的是，液体质点在泵体流道内的圆周速度小于叶轮的圆周速度。
应用推荐