A serial port connection using mobile phone short message sending module source.
一个利用串口连接手机模块发送短消息的源码。
Protocol also handles the sending and receiving of messages using a datagram or serial port connection.
Protocol还处理使用数据报或串行端口连接的消息发送与接收。
In this case, you must configure the target computer to accept a serial-port-to-serial-port connection.
在本例中，必须配置目标计算机以接受串行端口到串行端口的连接。
In this article, we show you how to register CIM event handlers with a a single specific connection port to avoid added complexity.
在本文中，我们将展示如何用一个特定的连接端口注册CIM事件处理程序以避免增加复杂度。
This connection will exist for the entire life of the listener port.
此连接将存在于侦听器端口的整个生命周期。
The server end of the socket is created on the machine where the server application is running and given a port, and it then listens on this port for a connection from a client application.
套接字的服务器端是在运行服务器应用程序的机器上创建的，服务器应用程序获得一个端口并在该端口上侦听来自客户端应用程序的连接。
They also facilitate connection of multiple SAS devices to a single initiator port.
它们还帮助把多个SAS设备连接到单一发起者端口。
The client end of the socket is created on the machine where the client application is running and given a port, and it then listens on this port for a connection from a server application.
套接字的客户机端在运行客户端应用程序的机器上创建，该客户端应用程序获得一个端口并在该端口上侦听来自服务器应用程序的连接。
If the port is already used for another engine connection, you will have to change the port number or specify a range of ports.
如果端口已经用于其它的引擎连接，那么您就需要更改端口号或者指定一个端口的范围了。
A client initiates a connection to a host (and a specific port) by sending a syn synchronize packet.
客户机通过发送syn同步数据包发起到一个主机(和特定端口)的连接。
However, the test server running within the tool will most likely use a different port, so you must configure the connection factory with the correct port number.
不过，在此工具中运行的测试服务器很可能使用不同的端口，因此您必须为连接工厂配置正确的端口号。
Configure HSQLDB connection properties, such as TCP port and administrator password.
配置HSQLDB连接属性，比如TCP端口和管理员密码。
Listing 2 shows an example of how to launch a VM in debug mode and listen for a socket connection at port 8765.
清单2是一个示例，显示如何在调试模式下启动VM并监听端口8765的套接字连接。
The listener port will always use one connection from the connection pool for running.
侦听器端口将始终使用连接池中的一个连接运行。
This connection will only be released after the listener port has been stopped.
此连接只有在侦听器端口停止后才释放。
The simplest form of a TCP port scan is to open a connection to all ports on a host.
TCP端口扫描的最简单形式是打开一个到主机所有端口的连接。
If you do change this value, make sure you also change the port specification for the SSL connection, as shown in Listing 2.
如果您更改了这个值，那么请确保同时更改ssl连接的端口规范，如清单2所示。
Because the HTTP adaptor is also available, you can try using MX4J (through a browser connection to port 8080) to manage the same methods and attributes.
由于HTTP适配器也是可用的，可以试着使用MX4J(通过一个到端口8080的浏览器连接)管理同样的方法和属性。
You will, however, need to change your topic connection factory port Settings from DIRECT to QUEUED prior to migrating your node.
您需要在移植节点之前将主题连接工厂端口设置由DIRECT改为QUEUED。
If it is not, make sure the network server is running on the port specified in the connection URL, and check to make sure all of the values are appropriate for your environment.
否则，确保网络服务器在连接url指定的端口上运行，并确保所有的值都适合您的环境。
The connection is established to the remote host on TCP port 22.
建立到远程主机的TCP端口22的连接。
It listens on port 563 (NNTPS) and waits for a connection.
它侦听端口563 (NNTPS)，并等待连接。
The second line shows an ESTABLISHED connection, where 192.168.1.147 is connected to port 445 on the local host (192.168.1.143).
第二行显示ESTABLISHED连接，其中192.168.1.147连接到本地主机(192.168.1.143)上的端口445。
Creating an event handler with single connection port.
用一个连接端口创建事件处理程序。
If you're connecting to the localhost: 4201 port, you should get a connection; otherwise, errors will appear in your console window.
如果是连接到localhost： 4201端口，则应该获得一个连接；否则，控制台窗口将会显示错误消息。
When nc is executed with the command-line parameters -l -p -c, it waits until it receives a connection to that port, and then it executes the command.
在使用命令行参数- l- p- c执行nc时，nc将一直等待，直到在该端口上接收到连接，然后执行指定的命令。
Configure iptables to allow only three connection attempts on port 2022 within 30 seconds.
配置iptables，以便在30秒内仅允许在端口2022上有三个连接尝试。
The browser makes a TCP connection to port 80 on the Web server with the returned IP address.
浏览器利用返回的IP地址与Web服务器的端口80构成一个TCP连接。
You configure Balance to forward connection attempts on a specified port to a channel group.
通过配置Balance，可以将一个指定端口上的连接尝试转发到一个通道组。
Searchd communicates to applications through a socket connection on port 3312.
Searchd将在端口3312上通过套接字连接与应用程序进行通信。
应用推荐