Parallel motion describes the movement of two parts in parallel.
平行进行用来描述两声部的平行运动。
Shock response of 6-dof parallel motion platform driven by hydraulic actuators is analyzed.
分析了六自由度运动平台系统受到外力冲击干扰情况下的位姿响应。
According to the method presented in the paper, "PTZS" vibrating-screen with parallel motion...
根据本文所述方法，已经研制成功了具有平动椭圆运动轨迹的PTZS振动筛。
Aircraft trailing edge devices, including devices with non-parallel motion paths, and associated methods.
飞行器后缘设备，含运动路径非平行的设备，和有关方法。
A front guide device is fixed on machine frame, and a back guide device can do parallel motion along the shaft line direction of the saw shaft.
圆锯片与锯轴通过花键连接，前导向装置固定在机架上，后导向装置可沿锯轴轴线方向平行移动。
Meanwhile, the 'time' registered in the passing of clouds, in the lifting of fog, in a rainbow, would by a parallel motion grow to be something of an embarrassment.
与此同时，表达着云的流逝、雾的上升和彩虹的“时间”通过类似的移动逐渐成为尴尬的代名词。
A integrated equation set for solving plane parallel motion of rigid body was derived, and the conditions of system of forces simplified on the center of mass plane was discussed.
给出了解决刚体平面平行运动问题的一组完整方程，讨论了力系简化在质心平面内的条件。
The method of parallel motion of response curve for lead ion-selective electrode in lead buffers is given to determine the stability constant of Pb-NTA complex in ethanol-water solvent.
本文提出了金属缓冲溶液中离子选择电极响应曲线平移法测定配合物的稳定常数。
Based on the initial value sensitivity of chaotic motion and the analysis of optimal searching process, a parallel adaptive chaotic optimization (PACO) method is proposed.
基于混沌运动的初值敏感性和对混沌优化搜索过程的分析，提出了并行自适应混沌优化方法。
A design scheme of motion control system based on parallel port of computer was proposed.
提出了一种基于计算机并行口的运动控制系统的设计方案。
The results will be useful for motion control of redundant parallel mechanisms and improving gross performance of parallel manipulators.
这些结论为冗余并联机构的运动控制以及靠冗余驱动提高机构性能提供参考。
The motion control of the hexapod parallel mechanism with high speed and high acceleration depends on the accurate dynamics model, proper simplification and real-time computing.
实现六足并联机构高速，高加速运动控制的关键在于所建动力学模型的准确表达、适当简化以及实时计算速度的满足。
Based on single particle motion theory, the motion of cylindrical particles in the parallel flow was studied.
根据单粒子的运动理论，研究了圆柱粒子在平行气流中的运动状况。
As an example, a planar five bars 2-dof parallel mechanism is discussed, the working space is drawn and the motion and force manipulation singularity are analyzed.
以平面五杆2 -DOF并联机构为例进行了机构工作空间分析、运动奇异位形分析、以及力奇异位形分析。
Aiming at the serial processing question existing in some typical search algorithms, this paper presents a fast motion estimation algorithm based on parallel processing principle.
该文针对传统搜索算法串行处理的缺点，提出了一种基于并行处理的快速运动估计算法。
It could carry through the motion control arithmetic of mono-CPU, parallel bi-CPU and layering multi-CPU and research on system support software.
它可以进行单cpu、并行双cpu和层次化多cpu的运动控制算法和系统支撑软件的研究。
In the part of motion estimation, we used the MMX instruction in the parallel calculation of the SAD.
在它的运动估计部分，对于sad值的计算采用MMX指令进行并行计算。
By adopting the method based on instantaneous motion analysis of mechanism, the distinguishing matrix for singularity configuration of 3-rtt parallel robot was established.
采用基于机构瞬时运动分析的方法，建立了3 -RTT并联机器人的奇异位形判别阵。
Firstly, utilizing the reverse screw, the characteristics of instantaneous motion of 3-RRRRR parallel mechanisms under its initial position and under the general condition were analyzed.
首先用反螺旋分析了3 -RRRRR并联机构在初始位置下和在一般情况下的瞬时运动特性。
Starting from the classical equation of motion, the mesoscopic parallel LC circuit is quantized.
从经典LC并联电路的运动方程出发，将介观LC并联电路量子化。
Parallel Indexing disk motion spectra is analyzed and researched, and the general criteria of design of motion spectra is proposed.
对平行分度凸轮运动谱的设计进行了分析研究，提出运动谱设计的准则。
From the rear, the legs move in almost parallel lines and in the same line of motion as the forelegs, converging slightly as the speed increases.
从后面观察，后腿差不多在平行的线上运动(与前腿相同的线)，随着速度增加，会略微收拢。
Finally, the input motion programming and dynamic planning of the flexible parallel manipulators were discussed, respectively.
最后，分别进行了柔性并联机器人系统的输入运动规划和动力规划。
An open CNC system with two CPUs in parallel, in which the center is PMAC motion controller and the supporting element is industrial PC, is suggested.
提出了一种以PMAC运动控制器为控制系统核心、工业控制机为系统支撑单元的双cpu开放式数控系统。
There are abundant and complicated singularities in parallel mechanisms, which have great effects on the accuracy, stiffness and motion ability of parallel mechanisms.
丰富而复杂的奇异位形是并联机构的一个重要特点，位形空间中的奇异位形对并联机构的精度、刚度以及运动性能有着重要的影响。
This paper studies the input motion programming method of flexible planar parallel manipulators.
本文研究了弹性并联机器人的输入运动规划方法。
A type of parallel micromanipulator with flexible hinges as the motion pair and magnetostrictive actuator as the driving rod is designed.
设计了一种以柔性铰链为运动副，磁致伸缩作动器为驱动支杆的并联微动机构。
A type of parallel micromanipulator with flexible hinges as the motion pair and magnetostrictive actuator as the driving rod is designed.
设计了一种以柔性铰链为运动副，磁致伸缩作动器为驱动支杆的并联微动机构。
应用推荐