An unknown system hardware failure detected.
检测到未知系统硬件故障。
The system hardware structure is carried out.
设计了群控控制器的硬件部分。
Firstly, clear the system hardware requirements.
首先，本文明确系统硬件要求。
A construction model of the system hardware is proposed.
提出了系统硬件的结构模型。
It interprets the system hardware, software, and experiment.
阐述了该系统的硬件、软件及实验。
The system hardware is composed of upper and lower computer.
系统硬件由上位机和下位机两部分组成。
The paper first introduced the system hardware system design.
论文首先进行了系统的硬件系统设计。
In the end, a practical system hardware platform is presented.
最后给出了一个实际的系统硬件平台。
The design methods of system hardware and software were described.
阐述了该系统的软、硬件实现方法。
Gives the control system hardware configuration and software design.
给出了控制系统的硬件配置和软件设计方案。
It designs system hardware configure and system software programming.
设计了系统的硬件配置和系统软件编程。
The system hardware was composed of upper computer and lower computer.
系统硬件由上位机和下位机两部分组成。
Structures of economic CNC system hardware and software are discussed.
研究经济型数控系统的硬件及软件结构。
The third chapter, LED display system hardware design and realization.
第三章，LED图文信息显示系统硬件部分的设计与实现。
Meanwhile, we refer to the system hardware as well as system transplant.
主要介绍此了系统的硬件及系统移植。
The system hardware architecture is described and the software is analyzed.
描述了所采用的系统硬件结构，并分析了软件结构。
The system hardware architecture and the general design of the program are given.
给出了系统的硬件结构以及程序的总体设计。
The inspecting principle, system hardware design and software flow are introduced.
介绍了该系统的检测原理、系统硬件设计和软件算法流程。
This paper presents principles and structures of the system hardware and software.
本文介绍该系统的硬件、软件的原理和结构。
Various sections of the system hardware and software design are introduced in detail.
详细介绍了系统硬件各部分组成和软件流程设计。
The system hardware circuity and software programming concept are presented in detail.
较详细地叙述了系统硬件电路构成和软件编制思路。
Finally, it comprehensively narrates the system hardware partially, software are partial.
最后全面地叙述了系统的硬件部分，软件部分。
The system hardware platform adopted the structure of distributed system based on network.
系统硬件平台采用了基于网络的分布式体系结构。
Then, focus on research and design of DSP-based Speech Recognition System Hardware Design.
接着，着重研究了基于DSP的语音识别系统的硬件设计。
The focus of this dissertation includes the Servo System hardware design and software design.
本文的重点主要包括稳定平台伺服控制系统的硬件设计和软件设计。
After the completion of the system hardware and software design, the system was actually tested.
完成了系统软硬件设计后，对系统进行了实际测试。
System principle, system hardware design, system software design and application were introduced.
本文介绍了系统原理、系统硬件设计、系统软件设计及实际应用情况。
The system hardware includes main control board, display and button board, and motor driver board.
系统的硬件电路板主要包括主控制板、显示按键板、电机驱动板。
In the article has produced the system hardware functional block diagram, the software flow chart.
文中给出了系统的硬件原理框图、软件流程图。
The program includes system hardware structure design and selection and Control program preparation.
该方案包括系统硬件结构设计、选型及控制程序的编写。
应用推荐