高速度低担搁。
Massive group correlation: The Internet now enables low cost, high speed, communication.
人际关系：网络现在能够提供低花费、高速度以及人际交往。
So it's all about the speed and simplicity and low cost.
所以最重要的是速度，便捷和低成本。
low and high. For mass production, a high speed horizontal mixer will be suitable.
对于大规模生产，宜用高速卧式混合机。
Luckily the train had been running at low speed following several hold-ups between stations.
幸亏有这一操作，使得列车在车站之间的几次拦截后以慢速行驶。
They briefly came into contact at a very low speed while submerged.
它们主要是在潜入水中时低速接触彼此。
Speed ratio is 1:5000, from low speed to high speed, all have steady torque characteristics.
调速比为1：50 00，从低速到高速都具有稳定的转矩特性。
Why do I have low downloading speed?
为什么我必须低下载速度？
You go from very high speed to some low speed, quite technical corners.
你从高速到低速，技术含量很高的弯角。
Flow of uniform pressure stability, low speed when the more apparent.
流量均匀压力稳定，低转速时更为明显。
The characteristics of this method are high accuracy, high speed, continuous measurement and low cost.
此方法的特点是：高准确度、高速度、低成本、并可连续测量。
Low speed mean, no draught is caused.
所谓的低速，就是不产生气流。
The characteristics of this method are high accuracy, high speed, Continuous measurement and low cost.
此方法的特点是：高精度、高速度、连续测量、低成本。
The system has high speed and low misdetection rate.
系统具有快速的检测速度，同时漏检率低。
This article introduces an air bubble method for low speed flow visualization in water tunnel.
本文介绍一种用于低速流动显示的空气泡方法。
High speed and low cost network is needed in process control area.
但工业控制领域需要一种高速廉价的网络。
The belt driven pump runs at low speed for an extended life.
皮带驱动的泵低速运行，以便延长寿命。
Direct-driven PMSG works at low speed and its size is generally big.
直驱永磁同步风力发电机运行转速低，一般定子外径都比较大。
From there the air fills up the room at very low speed.
新风以非常低的速度充满整个房间。
The new type of car features high speed, small size and low cost.
那类新型汽车以下速、小型战低用度为特性。
The water was rough and, despite our low speed, we were drenched by spray.
水上风浪很大，尽管我们的航速不快，飞溅的浪花仍湿透了我们的全身。
The drawing stress increased with the speed rise at low speed.
在低速拉拔时，拉拔应力随拉拔速度的增加而增大。
Very good speed characteristic of high speed mold closing and low pressure mold protection.
高速闭模、低压模保速度特性甚佳。
The low speed bottom sweep provides proper heat transfer to tank walls.
低速底部可以将适当的热量转移到罐壁。
Low ultimate pressure, high pumping speed for Ar.
极限压力低、抽气压力范围宽，对氩气抽速较高。
高速度，低拖延。
Because of the limitation of bandwidth, signal must be transmitted in low speed.
由于受传输带宽的限制，要求信号以较低的速率传输。
Because of the limitation of bandwidth, signal must be transmitted in low speed.
由于受传输带宽的限制，要求信号以较低的速率传输。
应用推荐