Create the source and target queues.
创建源和目标队列。
To create the source and target queues.
为了创建源和目标队列，要。
Case 3: Source and target are the same database.
案例3：源和目标是相同的数据库。
Examples of properties are the source and target.
属性的范例可以是源和目标。
To create channels between the source and target.
为了创建源和目标之间的通道，要。
Create datastores for source and target databases.
为源和目标数据库创建数据存储。
The source and target table definitions must match.
源表和目标表定义必须匹配。
Create connections to both the source and target servers.
创建到源服务器和目标服务器的连接。
But what if the source and target platforms are not the same?
然而，如果备份源和备份目标的平台不同又该如何呢？
Multiple triggers can be defined on source and target tables.
可在源表及目标表上定义多个触发器。
Source and target table compression specifications must match.
源表和目标表压缩规范必须匹配。
It will even notice if you mix up the source and target classes.
它甚至会注意到您是否混合了源类与目标类。
To define the Ajax source and target, perform the following steps
执行下列步骤来定义Ajax源和目标
Create tables in source and target datastores for CDC replication.
在用于cdc复制的源和目标数据存储中创建表。
Establishes a relationship between a source and target object.
建立源对象与目标对象之间的关系。
With this method, you select or create the source and target interfaces.
使用此方法，您将选择或创建源和目标接口。
Both source and target tables are protected by the same security policy.
对于源表及目标表采用相同的安全策略进行保护。
Click on the configure button and configure both source and target.
单击Configure按钮，并配置源和目标。
The report contains row counts from both source and target databases.
这个报告包含源和目标数据库的行数。
VMware command, with a different path to the source and target locations.
VMware命令，为源和目标位置使用了不同的路径。
You can get the source and target objects tied together by a relationship.
获取通过一个关系绑定在一起的源对象和目标对象。
Figure 1 shows an example where the source and target table rows are merged.
图1展示了一个例子，其中源表与目标表合并了。
Must define the tables, to be replicated, in the source and target databases.
必须定义源和目标数据库中要复制的表。
Make sure that the source and target are selected, and then click Finish.
请确定source和target都是选中的，然后单击Finish。
Also, the nested loop join method is used to join the source and target tables.
而且，嵌套循环联接方法用于联接源表与目标表。
In this article series, you use the DB2 Connector in source and target contexts.
在这个系列文章中，您将在源和目标上下文中使用DB 2Connector。
For example, suppose we have the following source and target as shown in Figure 8.
例如，假设我们具有如下源和目标，如图8所示。
The type of connection it creates depends on the source and target that you select.
它所建立的连接类型取决于您选择的源和目标。
The previous 2 sections have established an understanding of source and target data.
通过前2节内容已经能够理解源数据和目标数据。
This section describes how to create datastores for your source and target databases.
本节描述如何为源和目标数据库创建数据存储。
应用推荐