它可被简单地设为零。
It should be set to zero otherwise.
否则，应该设置为0。
These bytes are reserved and set to zero;
这些未使用字节被保留并被设置为0；
This member is no longer used and is always set to zero.
（这个成员已经很久没有使用，总是设置为零。） ）
If priority is set to zero, RUNSTATS will run unthrottled.
如果将优先权设置为零，也能不加调整地运行RUNSTATS。
This member is no longer used, and is always set to zero.
这个成员已经很久没有使用，总是设置为零。
Fix the bug while refresh intervals set to zero or blank.
当自动刷新时间设为零或空白，该网页仍继续刷新。已修正错误。
I double-check with him that my altimeter is set to zero .
我和他反复确认了我的高度计已经设置在了归零的状态。
IDThis member is no longer used and is always set to zero.
这个成员已经很久没有使用，总是设置为零。
In the case shown in Listing 1, the atomic counter is set to zero.
在清单1的情形中，原子计数器被设置为0。
If this property is set to zero, the text appears on the baseline.
如果这个属性设定为零，文字会出现于基础上。
If the specified line is out of range, the start line is set to zero.
如果指定行超出范围，起始行则设为零。
The calibration device shall be set to zero before calibration is started.
校准设备应设置到零，校准开始前。
If it is set to a value of 0 (zero), no time limit will be applied.
如果将此值设为0(零)，则不应用任何时间限制。
We don't get to set any of them to zero, right?
这里面没有等于零的？
We set "tel" to the initial value of zero.
我们将“tel”的初值设置为0。
To turn this feature off, set this property to zero.
要关闭此功能，请将此属性设置为零。
If it is set to a value of zero, no limit will be applied.
如果将其设置为零值，则不应用任何限制。
I will set them again to zero and now we get one onto double the mass.
我们将它重新调零，再放一个让质量增倍。
First let's set the external pressure equal to zero.
首先，让外部压强为零。
And you can set your energy reference to be zero.
能量的参考点可以任取。
Set the counter to zero and you will know where the recording starts.
将计数器定到零，你就会知道录音从哪儿开始。
Set the counter to zero and you'll know where the recording starts.
把计数器拨到零，你就会知道录音从哪儿开始。
our molecular translational energy, we'll just set it to zero.
我们的能量，我们分子的平移能量。
将SHEAPTHRES设置为0 (zero)。
This value will only be meaningful when util_impact_priority is set to non-zero.
这个值只在util_impact _ priority设置为非零值时有意义。
In the Image Parameters TAB set all VP values to zero.
在图像参数标签设置所有副总价值为零。
Therefore set gravity and drag it to zero.
因此设置重力，并将其拖动到零。
If you don't need diffuse scatter, just set it to zero.
如果你不需要，可以把它设为零。
Why did I set the interval to zero?
为什么我设定的时间间隔为零？
应用推荐