Issue the command on the primary server.
在主服务器上发出该命令。
This command should be issued on the home mail server of the mail file owner.
该命令应该在邮件文件所有者的主邮件服务器上发出。
After a warning, the POP3 server is ready for the next command.
在一个警告之后，POP3服务器准备下一个命令。
In the screen shot below, a command line access to an FTP server is shown.
下面的屏幕快照显示了对FTP服务器进行的命令行访问。
In this case, it is the default START command of an application server.
在本例中，它是应用服务器的缺省START命令。
Note that only the control region start command is needed to start a server.
请注意，启动服务器只需要控制区域START命令。
Make sure that the server started when the command is executed.
确保执行命令时服务器是启动的。
Run this command to start the container server
运行此命令，以启动容器服务器
To stop the server, you issue the same command with shutdown instead of start.
要停止该服务器，您可发出相同的命令，但要用shutdown代替start。
First, start up your Geronimo server with the following command line.
首先，使用如下命令行启动您的Geronimo服务器。
Then, bring up the server with the following command line
然后，请按如下命令行启动服务器
To timeout a client, run the following command from the server machine
可以在服务器计算机上运行以下命令设置客户机超时
Open a db2 command window on the system where the application server is installed.
在安装应用服务器的系统上，打开一个db 2命令窗口。
To determine if you have message contention, issue the server console command SHOW STAT MAIL.WAITING.
为了了解是否存在消息争用，发出服务器控制台命令showSTAT MAIL .WAITING。
Use the idsicrt command to create the directory server instance.
使用idsicrt命令创建目录服务器实例。
To stop capture, issue the following command from the Sun server.
要停止捕获，从Sun服务器发出以下命令。
To stop apply, issue the following command on the Windows server.
要停止应用，在Windows服务器发出以下命令。
To stop the server again, just press Ctrl-C at the command prompt.
只需在命令提示下按Ctrl - c组合键就可以再次停止服务器。
Enter the command ./start_streams_vwap.sh to start the Streams server.
输入命令./start_streams_vwap.sh 来启动Streams服务器。
Run the elb-describe-instance-health command to see the status of each server in the pool.
运行elb -describe - instance- health命令查看池中每个服务器的状态。
And you can run the same command at the server level by using this syntax.
您可以使用以下的语法来在服务器层次上运行相同的命令。
The server implements the Command pattern, so it can add new commands very easily.
服务器实现Command模式，所以它非常容易添加新命令。
To use the command line to instrument an application server, follow these steps.
要使用命令行安装测试应用程序服务，需要以下步骤。
Servername is the target WebSphere Application server for the command.
servername是命令的目标WebSphereApplicationserver。
Stop execution of command and downloading of the file from Source Server.
停止执行命令并停止从源服务器下载此文件。
Stop execution of command and downloading of the file from Source Server.
停止执行命令并停止从源服务器下载此文件。
应用推荐