With high temperature heat insulation plate, block heat temperature radiation effectively.
③。 加装高温隔热板、有效阻挡热温辐射。
Temperature becomes uniform by heat conduction until finally a permanent state is reached.
通过热传导，温度变得一致，直到最终达到一个恒定状态。
So it's easy to get into the high temperature limit, in that case. Where you basically see a temperature independent heat capacity.
所以它很容易到高温极限，在那种情况下，你基本上就能看到，不依赖于温度的热容。
The heat of vaporization is actually temperature dependent.
实际上，汽化热与温度有关。
If there's no heat flow between the b and c, then I can say all right, a and c were the same temperature.
如果在与之间没有热量流动，那么我就可以说，好吧与处于相同的温度。
And then the heat capacity, which is this often a very simple thing to measure, you change the temperature.
对于比热，这是一个比较简单的可测量，我们改变温度。
I'm going to start sucking in heat, to try to get the temperature down.
我要开始吸热了，试图将温度降低。
In no way does the temperature equal the amount of heat.
温度绝不等于热量。
So in that case, the high temperature limiting heat capacity is zero.
所以在这种情况下，高温极限的热容是零。
Brown tissue helps to regulate body temperature by generating heat.
褐色组织通过生成热量帮助调节体温。
What was the low temperature limit of the heat capacity?
热容的低温极限是什么？
Why did the heat capacity go to zero at low temperature?
为什么热容在低温时是零？
What's the heat capacity at high temperature?
高温时的热容是什么？
It exhibits high strength, rigidity, and good heat distortion temperature.
它具有高强度，刚度和良好的热变形温度。
It also takes just three minutes to heat up to its top temperature of 200c.
它也只需要3分钟就能加热到它的最高工作温度——200摄氏度。
Impact heat distortion temperature and low; temperature impact strength.
提高热变型温度和代温冲击强度。
Heat will flow from a body at high temperature to one of lower temperature.
热会从温度高的物体流向温度低的物体。
Finally, the influence on the economy of the heat source temperature is presented.
最终本文提出了热源温度的经济性影响的问题。
The initial temperature of solid heat carrier has great influence on the gas composition.
热载体初始温度对热解气组成影响显著。
And then heat it to appropriate temperature in order to reach necessary intensity and toughness.
再加热到适当的温度以达到所需的强度和韧性。
The amount of heat per mole necessary to cause the rise of temperature is different in each case.
在每一种情况下，致使每一摩尔物质升高温度单位所需要的热量是不相同的。
"The highest use temperature" is the basis of heat resistance insulation materials.
“最高使用温度”就是绝热材料耐热性的依据。
The indoor heat environment by indoor air temperature and quality of retaining structure surface temperatures.
室内热环境质量受室内空气温度和围护结构表面温度的影响。
SCR components will heat at work, so that high temperature equipment.
可控硅元件在工作时会发热，使设备内温度很高。
Heat shrink temperature and breaking strength tests were carried out.
分组测定热皱缩温度及断裂强度。
In an adiabatic system, this heat release serves to increase the chamber temperature.
在一绝热系统中，放出的热量增加了房间的温度。
The directions say to heat the water to room temperature.
说明里说需要把水加热到室内温度。
Improved heat distortion temperature and low temperature impact strength.
提高热变型温度和低温冲击强度。
Improved heat distortion temperature and low temperature impact strength.
提高热变型温度和低温冲击强度。
应用推荐