SCM AT89C52 is used as control center of the system, and system software was compiled with C51.
系统核心控制采用AT89C52单片机，并用C51编写全部软件。
C51 prepared through the buttons adjust brightness led procedures, have an adjustable timer with PWM.
C51编写的通过按键调节led灯亮度的程序，用定时器产生可调pwm。
The modular programming approach is adopted on the software design and code is writed in C51 language.
软件部分采用模块化程序设计方法，用C51编写代码。
Software development adopts C51, which improved the development efficiency and reduced the development cost.
采用C51进行软件编程，大大提高了开发效率，降低了开发成本。
It is written in a C51 liquid crystal display of the temperature measuring device, can display the measured temperature.
这是用C51编写的有液晶显示的温度测量仪，能显示测量的温度。
The paper states the method which is used to develop serial communication for MCU and PC with programming tools VB and C51.
本文详述了使用VB和C51实现PC机和单片机串行通信的开发方法，并简要地介绍了VB通讯控件及其使用方法，给出了调试程序。
Using C51 to programme DS1302 can strengthen the common use and transferability of DS1302, thus having certain practical value.
用C51对DS1302进行程序设计，能加强DS1302的通用性和可移植性，有一定的实用价值。
In this paper, the software of the system was designed based on modular design concept, and programming language C51 was adopted.
本文在软件设计方面采用模块式的设计理念，采用C51语言进行编程。
The operation principle of TSC51 Single Chip Micyoco(SCM) experimental device and the compiling process of KEIL C51 were analyzed.
分析了TSC51单片机实验仪的工作原理，阐述了KeilC51编译器编译工作过程。
The system is programmed by C51 language. It consists of eleven modules that each of them will achieve its corresponding function.
系统的软件设计由C51语言编程来实现，系统由十一个模块构成，各个模块完成特定的功能。
The program in single chip computer is C51 program, using the interrupt that UART receive end and the interrupt that UART send end.
单片机端通信程序采用C51编程，使用UART接收结束中断、UART发送结束中断。
It introduces the design of a liquid level measurement system based on the C51 single chip microcontroller and optical fiber technique.
介绍了一种基于C51单片机和光纤技术的液位测量仪的系统设计。
It provides the main system hardware circuit diagram and software flow frame and the main programme source code written with C51 language.
文章给出了主要的系统硬件电路图和软件流程框图，及用c 51语言编写的主程序源代码。
This dissertation is mainly about designation of the hardware circuit and system programming with C51 according to the designing objective in length.
阐述了该系统的硬件电路和系统软件处理程序的设计方法；
The hardware interface between the X5045 chip and the single-chip microcomputer AT89C52 and its corresponding software program using C51 are described.
给出了X5045芯片与AT89C52单片机的硬件接口电路，用C51语言编写了其软件接口程序。
During the use of C51 language, the problems of the configuration of the file, edit program, compile program, link program are analyzed and the methods of which are given.
在C51语言应用过程中，对配置文件设置、编写应用程序、编译应用程序、连接应用程序时容易出现的问题进行分析，并提出解决的方法。
The software designs adopt assembly language, C51 language to compile data sampling program and programs on protocol processing and data transfer conducted to USB interfacing chip.
软件设计中采用汇编语言、C51语言编写数据采集程序和对usb接口芯片进行协议处理及数据交换的程序。
The thermo-element measured the warm C51 procedure, may simultaneously measure 7 group different type the thermo-element, does zero some with a group copper resistance to compensate.
热电偶测温C51程序，可以同时测7路不同种类的热电偶，用一路铜电阻做零点补偿。
Presents the internal configuration of LCD module MSC-G12864 and its operation method. On these, discuss the interface with MCU and gives out programming method and some C51 program.
以应用广泛的MSC -G12 864液晶显示模块为例，在简单介绍内部结构与操作方法的基础上，讨论了其与单片机的接口以及相应的C5 1编程方法和程序。
"The design and implementation of data acquisition circuit based on C51" is the circuit PCB designed and implemented according to data of water situation of modern conservancy industry.
“基于C51的数据采集电路pcb的设计与制作”是针对现代水利行业水情数据采集而设计制作的电路pcb。
On the basis of the above an interface circuit of T6963C LCD controller which is controlled by 8051 singlechip is given using C51 hardware language. The paper also takes display method …
在此前提下以C51硬件开发语言为基础，给出了8051单片机与T6963C的接口电路框图，并以字符、图形的具体显示方法为例简要介绍了软件的设计流程及实现。
With this experiment board, the beginners can easily to grasp the principle and application of the Monolithic integrated circuit, be familiar with assemble languages, even the C51 languages.
采用本仿真开发实验板，可使初学者迅速掌握单片机原理及应用，熟悉汇编语言、甚至单片机c语言。
C51 program has been set the schedule of reading and writing status for controller. It can work out some operations of writing instruction code, writing data code, clear screen and roll screen.
用C51程序设置对于控制器的读、写状态的时序，从而实现对于控制器的写指令代码、写数据代码、清屏幕、屏幕滚动功能的操作。
Local controller card take charge of incepting the control command from monitoring center. They are all controlled by singlechips, C51 and 51 assemble were used to develop the controlling software.
现场监控器由数据采集卡和网络通讯卡组成，现场控制卡负责接收监控中心发出的控制命令，它们都是由一块51单片机控制，其软件开发都是使用了C51和51汇编程序。
Local controller card take charge of incepting the control command from monitoring center. They are all controlled by singlechips, C51 and 51 assemble were used to develop the controlling software.
现场监控器由数据采集卡和网络通讯卡组成，现场控制卡负责接收监控中心发出的控制命令，它们都是由一块51单片机控制，其软件开发都是使用了C51和51汇编程序。
应用推荐