第三章论述了本设计的系统硬件设计。
In the third part I discuss the hardware design of the system.
单片机系统硬件设计。
系统硬件设计及调试。
重点阐述了系统工作原理、系统硬件设计和软件设计。
The system's general principle, hardware and software design are mainly discussed.
介绍了该系统的检测原理、系统硬件设计和软件算法流程。
The inspecting principle, system hardware design and software flow are introduced.
本文介绍了系统原理、系统硬件设计、系统软件设计及实际应用情况。
System principle, system hardware design, system software design and application were introduced.
提出了系统硬件系统设计的一般思想和方法。
And, proposes the general thought and method of the hardware system design.
通过交叉调试，完成了该嵌入式控制系统的整个软件和硬件的设计工作。
The design of hardware and software of whole embedded system have been made by cross-debug.
重点介绍了系统组成、硬件和软件设计。
The system configuration, design of hardware and software are emphasised.
论述了它的工作原理、系统组成和硬件设计。
It describes the principle, system configuration and hardware design.
其次，设计了敏感皮肤的信号处理硬件系统。
Secondly, it discusses the signal processing hardware system of sensitive skin.
本论文包括硬件设计、驱动程序开发和组成CAN总线控制系统三部分。
The dissertation consists of hardware design, driver development, CAN bus control system composing.
给出了控制系统的硬件构成，软件设计思想和实际应用结果。
The hardware constitution, design thought of software and actual application results are given.
航标遥测系统的设计分为硬件设计和软件设计两部分。
The design of navigation mark telemetering system is comprised of hardware design and software design.
设计了系统的硬件配置和系统软件编程。
It designs system hardware configure and system software programming.
阐述了系统硬件组成，监控系统设计和系统保护的功能与特点。
It is introduced that the system of hardware, monitoring and control system and protected function.
最后，在软硬件设计的基础上，进行了驱动系统的试验调试。
Finally, on the basis of software and hardware design, the experiment has been done on the drive system.
测试系统硬件电路设计。
硬件系统设计。
文章详细给出了系统的设计方法、硬件结构及软件流程。
Design method, hardware structure and software process of the system are introduced in detail.
详细介绍了该系统的硬件设计和软件实现。
The hardware design and software realization of the system were introduced in detail.
具体给出了参数检测系统的硬件设计及软件控制流程。
The hardware design and software flow chart of the parameter test system were give out.
介绍了系统结构，总体方案设计，硬件设计和软件控制流程。
System structure, scheme design, hard - ware design and software control process are introduced.
文中给出了系统硬件、软件的设计。
The hardware and software design of the system is presented.
介绍了热电偶自动检定控温系统的硬件设计。
It introduced the hardware design of temperature control for the thermocouple auto-verification system.
介绍了灰色预测控制系统软、硬件的设计；
Then, the design of hardware and software systems of GPC is introduced.
完成电梯群控系统的硬件设计。
The hardware of elevator group control system has been designed.
详细的讨论系统的硬件设计。
硬件系统设计。
本文重点阐述了该系统硬件电路方面的设计。
应用推荐