Figure 7 compares all five governors with ondemand and conservative threshold tuning.
图7比较所有5个调控器,其中ondemand和conservative的阈值进行了调优。
If you set this value to 100, the governor will act exactly like the ondemand governor.
如果把这个值设置为100,这个调控器的表现会与ondemand调控器完全一样。
Now we'll compare how the tuned ondemand and conservative governors behave with this workload.
现在我们将比较调优的ondemand和conservative调控器在这个工作负载下的表现。
If you load the ondemand governor, you will see a directory called ondemand in the cpufreq directory.
如果装载ondemand调控器,会在cpufreq目录中看到ondemand目录。
In this section, I'll compare the tuned ondemand and conservative governors to the other three governors.
在这个小节中,我将比较调优的ondemand和conservative调控器与其他3个调控器。
If the governor is set to conservative or ondemand, you will also see a directory of the governor's name here.
如果调控器设置为conservative或ondemand,还会在这里看到与调控器同名的目录。
Note that any changes to the ondemand settings will be applied systemwide so you will not need to change the setting for each processor.
注意,对ondemand设置的任何修改会应用于整个系统范围,所以不需要为每个处理器修改设置。
The conservative governor is the most power-efficient for a load of 8-12 percent utilization, closely followed by the ondemand governor.
conservative调控器在8 - 12%的利用率负载水平上的能效最高,紧随其后的是ondemand调控器。
Figure 3 compares the ondemand governor's effectiveness running the default configuration, an up_threshold of 80 versus the tuned ondemand governor, running with an up_threshold of 98.
图3比较ondemand调控器以默认配置(up _ threshold为80)运行的效果和以调优后的设置(up _ threshold为98)运行的效果。
Here you can see that for almost every load, the tuned ondemand governor with an upwards utilization threshold of 98 is slightly more power efficient than the default ondemand governor.
从图4可以看出,对于几乎每一个负载水平,调优后的ondemand调控器(利用率阈值为98)比默认ondemand调控器的能效都略高一些。
Configure the OnDemand instance on Saturn.
在saturn上配置OnDemand实例。
Install the OnDemand software on both nodes.
在两个节点上安装OnDemand软件。
The following command will start the OnDemand instance.
下述命令将启动OnDemand实例。
Create the OnDemand database and test the instance on Saturn.
创建OnDemand数据库并在saturn上测试该实例。
Verify that the cluster is up and running on both nodes and that you can access OnDemand via the Windows client.
检查群集是否启动并在两个节点上运行,能够通过Windows客户机访问群集。
The saturn_svc adapter will be configured for IPAT since this will be the address to which the OnDemand clients will connect.
saturn_svc适配器配置用于IPAT,因为OnDemand客户要连接的就是这个地址。
Verify that the cluster migrates all the resources and starts the OnDemand application on cassini and that you can access it via the Windows client.
检查群集是否迁移了所有资源,在cassini上启动OnDemand应用程序,看看能否通过Windows客户程序访问它。
Note: The server configuration information for the OnDemand client should not need to be changed. You should still be able to access the OnDemand server even though it is actually running on cassini.
提示:OnDemand客户的服务器配置信息应该不需要修改,虽然 OnDemand实际上运行在cassini 之上,但您应该仍能访问它。
Note: The server configuration information for the OnDemand client should not need to be changed. You should still be able to access the OnDemand server even though it is actually running on cassini.
提示:OnDemand客户的服务器配置信息应该不需要修改,虽然 OnDemand实际上运行在cassini 之上,但您应该仍能访问它。
应用推荐