Prediction of cutting force has become an important aspect in HSM.
切削力的预报是切削加工的重要研究方向。
The crystallographic nature of cutting force variation was analyzed based on crystal plasticity.
作者还根据晶体塑性力学理论，分析了产生这种变化的根源。
The singular index of cutting force signal is proposed as a parameter for detecting cutter's wear.
提出采用切削力信号的奇异性指数作为衡量刀具磨损的参量。
The real-time obtaining of cutting parameters is one of the key technologies of cutting force prediction.
切削用量的实时获取是切削力预测的关键技术之一。
Impact cutting and cutting compared, not only can increase depth of cut, but can also reduce the large number of cutting force.
冲击切削与静压切削相比，不仅可以增大切削深度，而且可以大量降低切削力。
Secondly, the paper has developed the collection of cutting force and analytical system on the basis of existing hardware and software.
其次，本文在现有的硬件及软件的基础上，设计和开发了切削力的采集及分析系统。
The article resolves the calculation problem of cutting force about the electrolytic nickel board and then corrects the formula of cutting force.
解决了实际电解镍成品板剪切力的计算问题，并对电解镍成品板的剪切力公式进行修正。
By the system, the cutter working condition on-line measurement and test can be made effectively on the basis changes of cutting force and spectral power.
这种系统能根据切削力及频谱能量的变化，有效地在线监测刀具工况。
Analysis is conducted for the variation of cutting force during the cutting process and the effect of negative shearing on the cutter damage is pointed out.
分析了切削过程中切削力的变化情况，并指出负剪切现象对刀具破损的影响。
This paper describes how to increase the productivity effect of cutter-suction dredgers in the fields of cutting force, dredging pump, gauge pile and exhaust pipe.
本文从绞刀、泥泵、定位桩装置及排泥管等四个方面，论述了提高绞吸式挖泥船生产效率的途径。
On the basis of cutting force model and vibration model of machine tools structure, the effect of the regenerative chatter on the stability of end milling is focused.
存得到切削力模型和机床结构振动模型的基础上，着重研究了再生型颤振对铣削加工过程稳定性的影响。
Using VC as a design platform, a real-time detecting and compensation system for tool wear based the analyzing and disposing for signals of cutting force is introduced.
介绍了以VC为平台设计开发的一套基于切削力信号分析与处理的刀具磨损实时监测和补偿系统。
Signals of cutting force and vibration are measured with multi-sensor and features in frequency domain and time-frequency domain are extracted by using wavelet package decomposition.
利用多传感器对切削力和振动信号进行监测，通过频率变换提取切削力特征量，采用小波包分解技术提取振动信号特征量。
The mechanism of cutting force, cutting temperature and tool wear in the machining of quenched steel and nickel based high temperature alloy with ceramic tools are analyzed in the paper.
重点分析了陶瓷刀具在切削淬火钢和镍基高温合金中有关切削力、切削温度、刀具磨损等方面的机理。
Through cutting experiments in which the contact length between chip and rake face of restricted contact cutter is reduced step by step, the variation principle of cutting force is studied.
通过切削试验，研究了限制接触刀具前刀面的刀—屑接触长度逐渐减小时切削力的变化规律。
The principle of coal-rock interface recognition is to pick up the response signals of cutting force of shearer by multi-sensor and process these data to achieve state of cutting coal or rock.
煤岩界面识别的基本原理是利用多类型传感器拾取采煤机截割力响应信号并对这些信息进行分析而识别煤岩界面。
The regression equation of cutting force meets the experiment result very well, the response curved face derived from the regression equation can help to choose proper high-speed cutting parameters.
切削力回归方程与实验高度符合，运用该回归方程作出的响应曲面有助于合理选择铝衬微波印制板高速铣削加工切削参数。
The regression equation of cutting force meets the experiment result very well, the response curved face derived from the regression equation can help to choose proper high-speed cutting parameters.
切削力回归方程与实验高度符合，运用该回归方程作出的响应曲面有助于合理选择铝衬微波印制板高速铣削加工切削参数。
应用推荐