An new method to design high reflectivity film.
高反射率光学薄膜的一种新设计方法。
Therefore, we will choose the second method to design the report.
因此，我们将会选择第二种方法来设计报表。
This paper presents a new method to design volume velocity sensor.
介绍了一种设计体积速度传感器的新方法。
The method to design master-servant clock linked with power-lines is given in his paper.
给出一种利用电力网传输时间信号的子母钟的设计方法。
This paper reports a method to design a system for computer-aided image diagnosis and study.
本文探讨设计一套计算机化的影像辅助诊断教学系统的方法。
A linearization method to design biorthogonal cosine modulation (BCM) filter Banks is proposed.
介绍了一种用于设计双正交余弦调制滤波器组的线性化方法。
Besides, this article introduces a method to design a multifunctional signal generator with 5g8038.
介绍了用5g8038设计多功能函数信号发生器的方法。
This paper also discusses how to use this method to design a good XML document and an example is given.
重点讨论如何通过数据建模设计出一个良好的XML文档，并简单介绍了一个XML文档实例。
The paper presents a new method to design a predictive filter which suits to analyze non-stationary data.
从三次样条函数入手，提出一种新的适合非平稳数据分析的预测滤波器设计方法。
The last part is conclusion, it is talking about important of fuzziness and method to design fuzzy space.
最后得出结论，探讨模糊性在当代设计实践中的意义与途径。
This article introduces a new method to design the waterproof property of moistureproof agent sealed floor.
本文介绍一种针对防潮剂封边地板的实际防潮性能而设计的新型测试方法。
On the basis of Chebyshev curve fitting method, a new method to design worn profile tread is proposed by this paper.
本文在切比雪夫曲线拟合方法的基础上，提出了一种高次曲线磨耗形踏面的设计方法。
In this article you learned about a method to design service-oriented applications based on software product lines principles.
在本文中，您了解了一种基于软件生产线原理来设计面向服务的应用程序的方法。
A new method to design an IIR filter is proposed under this condition of infinite impulse response given from a new Angle.
文章从一个新的角度提出了一种在给定冲击响应条件下IIR滤波器的设计方法。
Moreover, a method to design the filter of convolution linearization is proved by using the statistic and the matrix theories.
同时，利用统计和矩阵理论，证明了设计“卷积线性化”滤波器的方法。
This paper proposes a new method to design state feedback controller for networked control system (NCS) with time-varying delays.
为带时变时延的网络化控制系统提出了一种新的状态反馈控制器的设计方法。
For a class of linear singular time-delay systems with uncertainties, we bring forward a new method to design a switching surface.
针对一类带有不匹配不确定性和不匹配干扰的线性奇异时滞系统，本文给出了一种新的切换面设计方法。
A method to design efficient radar wideband digital quadrature demodulation receiver is described. The design condition is also given.
描述了一种高效的雷达宽带正交接收机的全数字设计方法，给出了设计条件。
This paper deals with the decoupling of multivariable control systems and presents a simple method to design dynamic compensator matrix.
本文讨论了多变量系统的解耦问题，给出了一种简便的解耦补偿矩阵的设计方法。
This article describes a new method to design and implement a progress bar and USES a simple application to demonstrate the main concepts.
详细描述了一种进度条的设计与实现方法，运用一个简单的应用程序示范了其设计思想。
This system used E-R chart method to design in order to minimum data redundancy and optimize data consistency and reduce updating abnormity.
本系统采用E -R图法进行规范化设计使得数据冗余最小，数据一致性好，更新异常问题不易发生。
A new method to design source-withdrawal weighting transducer is presented, which avoids the complexity when using traditional design methods.
提出了极性抽指加权叉指换能器设计的新方法，克服了传统设计方法的繁杂性。
A novel rapid method to design optimal-fuel interplanetary trajectory for low-thrust propulsion is presented based on normal trajectory approach.
针对星际探测任务中燃料最省小推力转移轨道问题，提出一种基于标称轨道的快速设计方法。
Using Mfhx method to design the experiment process, we study the technology for extraction and isolation of the holothurian glycosaminoglycan (HG).
采用计算机优化实验设计方法研究了海刺参粘多糖的提取、分离工艺。
This thesis put forward a method to design and simulate a kind of waveguide component and will help to design other integrated waveguide components.
本文提出了一种集成光波导器件的数值模拟设计及优化方法，对其他的集成光波导器件的设计有着指导参考价值。
This article demonstrates a method to design a load test tool for Radio Network Controller (RNC), and specifies the hardware and software realization.
本文阐述了无线网络控制器(RNC)话务负载测试工具的基本设计方法，及其测试环境和软件的实现等。
This paper presents a method to design an intelligent control program for PLC according to its characteristics. It has been used in the jigging control.
本文依据PLC的控制特点，提出了一种PLC智能控制的程序设计方法，并在跳汰机的控制中得到了应用。
This paper presents a new method to design the disk CAM with concave follower, and find the relationship between the new kind of CAM and the formal ones.
本文找出了凹圆弧底直动从动件盘形凸轮与原有凸轮之间的区别与联系，并统一了原有凸轮的设计方法。
This paper presents a new method to design the disk CAM with concave follower, and finds the relationship between the new kind of CAM and the formal ones.
找出了凹圆弧底直动从动件盘形凸轮与原有凸轮之间的区别与联系，并统一了原有凸轮的设计方法。
This paper presents a new method to design the disk CAM with concave follower, and finds the relationship between the new kind of CAM and the formal ones.
找出了凹圆弧底直动从动件盘形凸轮与原有凸轮之间的区别与联系，并统一了原有凸轮的设计方法。
应用推荐