With the temperature rising, polar ice will melt at a faster rate.
随着温度的上升，极地的冰会以更快的速度融化。
The temperature has risen just enough to melt snow but not enough for Little League practice to start.
气温刚刚上升到足以融化积雪的程度，但还不足以让小联盟的训练开始。
The peak cobalt rodlet temperature doesn't exceed the cobalt melt temperature during these two cases.
在这两种情况下，钴小棒的峰值温度不会超过钴的熔化温度。
They note that pressure and the temperature inside the reactor core remain at levels far lower than what would further melt the core.
他们指出，该反应堆堆芯现在保持的压力与温度并不高，远远低于会导致堆芯进一步融化的水平。
That raises the temperature of the sea, making the ice melt even faster.
这就会提高海水的温度，导致冰的融解速度加快。
Gallium is solid at room temperature but will melt if held in your hand, caesium (Cs), and francium (Fr) ?the second rarest naturally occurring element, can also be liquid at or near room temperature.
金属镓在室温里是固体状态但是把它放在你的手上它就会融化，金属铯，元素钫这些比较稀有的元素在室温或者接近室温的情况下是液体状态的。
PHB copolymers are preferred for general purposes as the degradation rate of PHB homopolymer is high at its normal melt processing temperature.
基丁酸酯共聚物是作为均聚物PHB的降解率一般用途的首选是在其正常高熔体加工温度。
The molder must recognize the dangers of excessive fill speed, insufficient injection pressure, excessive melt temperature, and inadequate packing.
注塑工必须认识过快填充速度、不足注塑压力、过高融化温度和不充分挤压的危害性。
Start by determining the true melt temperature and set the die body to that temperature.
从确定真正的熔体温度开始，然后按照这个温度设定口模体的温度。
Metals will melt when heated to a certain temperature.
金属加热到一定的温度都会熔化。
On the other hand, by improving the control of the melt temperature, it can distinctly reduce the waste of energy, pull the cost down and enhance the efficiency of extrusion.
另一方面，通过加强对物料的温度控制，可以减少能量的浪费，降低生产成本，提高挤出效率。
Unmelted gels have the same melting point as the surrounding resin, but remained colder than the average melt temperature.
不熔凝胶与周围树脂有同样的熔点，但是受热温度比平均温度低。
They melt at a higher temperature than the surrounding resin.
它们的熔融温度比周围的树脂高。
Expect the melt temperature to rise somewhat.
希望把熔体温度升高一些。
On the contrary, when melt temperature is too low, the melt viscidity becomes intensive, so cavitation and acoustic streaming are in no effect.
如果施振温度过低，熔融合金粘度就会增大，致使声空化和声流效应发挥不了应有的作用。
The effects of pressure and frequency on ABS samples of different melt temperature under vibration field were studied.
研究了在振动场作用下，ABS试样在不同的温度熔体下受振动压力和频率的影响。
The influences of processing parameters, material properties and screw design on melt temperature distribution in reservior during injection moulding are described in this paper.
本文叙述了注射成型中加工参数、物料性能及螺杆结构对存料区熔体温度分布的影响。
Process window analysis, another part of mold flow analysis, examines melt temperature, mold temperature, injection pressure, and fill times.
加工窗口分析、它零件的模流分析，检查熔体温度、具温度、塑压力和充填时间。
The melt flow index of the blends was increased when the content of PEEK was decreased and melt temperature was increased.
结果表明：共混物的熔体流动指数随PEEK含量的降低和熔体温度的升高而增加；
That means there is no feedback from any other measurement that would alter the melt temperature, nor is melt temperature used to control anything else.
这就意味着没有什么测量反馈来改变熔体温度，熔体温度也不用于控制别的什么东西。
The static and dynamic mechanical properties have been studied for PP that have been injected at different melt temperature and mold temperature.
本文研究了在不同的熔体温度和模具温度下，注射成型的聚丙烯塑料试样的静态和动态力学性能；
Our results show that mechanical properties of PP samples strongly depend on the melt temperature and mold temperature.
实验结果表明，熔体温度和模具温度对试样的力学性能有重要影响。
The effects of the moisture content in polyester chip, the melt temperature and pressure, and the shear rate on the shear viscosity are discussed.
探讨了聚酯切片含水率、熔体温度、熔体压力、切变速率对熔体切变粘度的影响。
The two kinds of viscosities were significantly affected by the rate of shear, melt temperature and 2, 7-naphthalenediol unit content.
而剪切速度、熔体温度及2,7 -萘二酚链节含量对此两种粘度有重大的影响。
Surface Imperfections: Melt temperature may be too high causing resin decomposition and gas evolution (bubbles).
外观不完整：塑料熔化温度过高导致树脂分解和气泡。
The effects of compact load, surface area and thickness of the pellets and the melt temperature on reaction of electro-deoxidation were investigated.
研究了试样的成型压力、烧结程度、表面积，以及熔盐温度和阳极碳棒直径大小等对电脱氧反应速度及脱氧产物氧含量的影响。
The melt temperature decreases linearly with the increase of the charge mass.
炉料质量与熔体温度呈线性关系，随着炉料质量的增大熔体温度降低。
The constant volumetric delivery and melt temperature reduction bring a significant improvement in the quality of the end product.
稳定的体积流量和降低熔体温度对于改善最终产品的质量有重要意义。
The constant volumetric delivery and melt temperature reduction bring a significant improvement in the quality of the end product.
稳定的体积流量和降低熔体温度对于改善最终产品的质量有重要意义。
应用推荐