A tolerance design method based on maximum tolerance region is presented in this article.
提出了基于最大容差域的容差设计方法。
ResultsIn the experiment of acute toxicity, the maximum tolerance dosage by gavage in mice was 160 times of the clinical dosage in humans.
结果急性毒性实验小鼠灌胃给药最大耐受量相当于人临床日用量的160倍。
Results Prevent-sick syrup was nontoxic. The mice maximum tolerance of anti-seasickness oral solution was 100 times higher than that of clinical dosage.
结果防晕船口服液基本无毒性，抗晕船口服液小鼠最大耐受剂量为临床剂量的100倍以上。
The dose limiting toxicity (DLT) of it was neutropenia and diarrhea. Its maximum tolerance dose (MTD) may be reduced by elevated liver or kidney function.
其剂量限制毒性(DLT)为中性粒细胞减少和腹泻，肝肾功能下降会降低最大耐受剂量(MTD)。
The test result shows that maximum tolerance of the simulated ambient pressure deviation is about 14% under which the engine thrust uncertainty remains less than 1.0%.
试验结果表明，在保证推力不确定度优于1.0%的条件下，拉瓦尔喷管发动机高空模拟试验的模拟偏差容限约为14%。
The permissible diameter variation (Vdmp, VDmp) is the tolerance for the maximum and minimum mean diameters of one measuring plane.
允许的尺寸变化量是考虑到了最大和最小平均直径公差的测量平面。
YH cable is working at low voltage (maximum voltage of 200v) under high current conditions, requiring a certain degree of tolerance.
YH电缆是在低电压(最高电压为200v)大电流的条件下工作，要求具有一定耐性。
The objective function of process tolerance optimization is established with the fuzzy mathematics based on maximum process capability.
以最大工序能力作为工序公差优化的目标，利用模糊数学的概念建立目标函数。
The maximum organics compounds tolerance of combination system and entrapping system were 50% and 38% higher than suspending system respectively.
另外，组合体系和包埋体系的耐受有机物最大限度分别比悬浮体系提高了50%和38%。
The function and the acceptance condition of maximum material requirement (MMR) and reversible requirement (RR) were analyzed through dynamic tolerance figure.
通过动态公差图，分析了最大实体要求（MMR）及其可逆要求（RR）的功能及合格条件。
And the dimensional tolerance is the difference between the maximum and minimum values of things.
和尺寸公差之间的区别是最大和最小值的东西。
Taking into account assembly tolerance and geometric tolerance, with the maximum and minimum method, a parallel degree calculating method for the missile launcher is put forward.
在考虑了装配公差和形状位置公差的条件下，采用极大极小法，给出了该型发射装置改进后的平行度计算方法。
If a maximum diameter is specified the tolerance shall be the total tolerance given in table 8 all under the maximum diameter.
如果指定了最大直径，公差应是表8中给出的总公差，所有的都低于最大直径。
In order to enhance the fault tolerance ability of the fault diagnosis model, information correction is thus adopted based on the maximum likelihood decoding theory.
为了提高模型的容错性，提出了基于最大似然译码原理的监测信号信息校正方法，然后利用编码基本网在无畸变信号的基础上进行故障诊断。
With regard to measure the spares that adopt maximum material requirement and don't ask shape and position tolerance, it is not accurate to measure with position gauge only.
该文论述了最大实体要求，可逆要求用于最大实体要求，最大实体要求用于基准要素三种情况下尺寸公差与形位公差相互补偿及计算问题。
There might be no profit or even a loss in business operation for the 1st financial year. What is the maximum loss tolerance of you for the 1st year (RMB)?
在第一年，您也许不会盈利或会亏损，您所能接受的最大亏损额是多少？（人民币）
With two meters by ruler of wall structure, inspection, shall not exceed 5 mm maximum deviation, cut or out-of-tolerance part should be picked with a than three repair cement mortar leveling.
对结构墙体，用两米靠尺检查，最大偏差不得超过五毫米，超差部分应剔凿或用一比三水泥砂浆修补平整。
With two meters by ruler of wall structure, inspection, shall not exceed 5 mm maximum deviation, cut or out-of-tolerance part should be picked with a than three repair cement mortar leveling.
对结构墙体，用两米靠尺检查，最大偏差不得超过五毫米，超差部分应剔凿或用一比三水泥砂浆修补平整。
应用推荐