The damaged presses of hot die forging should be superseded by the modern presses;
已损坏的热模锻压力机用新型设备取代；
Bruce suggested: hot die steel including forging, hot extrusion and die-casting of steel.
布鲁斯建议：热作模具钢包括锻压、热挤压和压铸模具钢。
It has elaborated the advantages replacing hot die forging with the cold forging technology.
阐述了用冷锻工艺代替热模锻的优点。
The numerical simulation of hot die forming process for upper core plate stock in railway was done.
对铁路用上心盘热模压成形过程进行了数值模拟分析，得到了上心盘成形过程的应力场、应变场。
Hot die forging, in addition to the hot work die steel casting, the wear and heat load large front steel casting mold is often used.
热作模具锻造中，除上述热作压铸模具钢外，磨耗及热负荷大的模具常采用铸型锋钢。
The article researches the effect of different hot die forging process parameters on forgings structure and properties of GH4169 alloy.
本文研究了不同热模锻工艺参数对GH4169合金锻件组织性能的影响。
Using laser cladding technique to harden the working surface of new hot die or repair the used one shows a good prospect in industrial application.
用表面激光熔覆技术强化模具表面或旧模具修复，具有广阔的应用前景。
The forming technology oft he upper body center plate in hot die forging and the characteristic of the die structure have been introduced with the analysis on the forming process.
从分析上心盘的成形过程出发，介绍了上心盘热模压成形工艺及模具特点。
The hot die forming and key technology of hydro-turbine blade have been introduced with discussion about the numerical simulation application in hydro-turbine blade hot die forming.
介绍了水轮机叶片热模压成形及其关键技术，并探讨了数值模拟技术在水轮机叶片热模压成形中的应用。
If the pond dried up, all of the fish would die under the hot, dry sun.
如果池塘干涸，所有的鱼将会被烈日晒死。
Form and dimension may also be achieved by a number of alternative processes such as hot or cold extrusion, sand casting, die casting, and precision casting.
形式和尺寸也可以通过其它一些可选工艺来达到，比如热挤出或冷挤出加工，沙模铸造，拉模铸造，或精密铸造。
A piece of hot metal sufficient to slightly overfill the die shape is placed in the bottom die, and the top die is forced against it, so that the metal takes the internal shape of the die.
将一块大小足以充填模腔并能稍有溢出的加热金属放入底模，并将顶模加压合拢，这块金属便获得该模腔的形状。
Figure 1 shows the male die of a hot extrusion planar combined die.
图1所示为一热冲压平面结合模具的公模简图。
All kinds of reasons of extruded die cracked is analysised when profile is hot extruded, and take the method of preventing and remedying.
分析了异型材热挤压时造成挤压模具开裂失效的各种原因，并提出了预防和补救措施。
A new type of austenite hot working die steel added copper is presented in this paper.
提出了一种新型的含铜奥氏体热作模具钢。
Transferring the hologram onto a substrate occurs at this point by hot stamping or die cutting the hologram onto the selected material.
全息图转移到基板发生在这一点烫金或模切到所选材料的全息图案。
The surface invalidation of H13 hot extruding gear die is analyzed, ion nitriding is used in order to improve H13 hot extruding gear die life.
对H13热挤压齿轮模的表面失效进行了分析，为提高H13热挤压齿轮模的寿命对其进行了离子渗氮。
The hot extruding forming technology and die design of high-voltage switch component LW8-35SF6 aluminum alloy pull-rod are analyzed.
分析了高压开关零件LW8 - 35sf 6铝合金拉杆的热挤压成形工艺及模具设计。
The paper studies the comprehensive technical measures to prolong the life of the hot press roll forging die.
本文介绍了提高辊锻热成形模寿命的综合技术措施。
So, in hot extrusion process, how to reduce wear and improve die life is one of the most concerned problems for mold designer.
因此，在热挤压过程中，如何减少磨损、避免局部磨损过大是设计人员最关心的问题之一。
Steel H13 (AISI) is one of materials which is widely used in making hot -working die.
H13(美国钢号)是使用最广泛的热作模具钢之一。
The new cast hot work die steel (CHD steel) has high strength and toughness, high thermal stability, high lifetime and wide application prospects.
新型铸造热锻模具钢（CHD钢）由于具有较高的强韧性和高温稳定性，使用寿命高于锻造模具，具有广阔应用前景。
The fine surface quality and dimensional accuracy cast hot work die was obtained by special sand V method casting technique.
采用特种砂v法铸造工艺获得了良好表面精度和尺寸精度的铸造模具。
With laser cladding Co-base alloy coatings, the high temperature hardness and thermal fatigue resistance of H13 hot-working die surface were appreciably increased.
H13 热作模具钢表面经激光熔覆钴基合金后显著提高了模具的高温硬度和热疲劳抗力。
Results showed that effect of using the hot spray-welding process to strengthening the hot-working die steel surface was good.
结果证明采用热喷焊工艺对热作模具钢表面进行强化的效果优良。
Thermal fatigue is one of the primary form of hot-work die steels failures.
热疲劳是热作模具的主要失效形式之一。
The corresponding relationship between high temperature impacting Numbers and wear loss of hot work die steels are studied by weight loss method.
用失重法研究五种热作模具钢的热磨损次数与磨损量的对应关系。
The forming technology and parameters for hot forging of the brass brake shield, and the structure and the working process of the die were introduced.
介绍了黄铜闸板热锻成型工艺和参数，还介绍了模具结构及工作过程，提出了在热锻过程中应注意的几个问。
Finally the design and application achievement of this hot forging die are described.
介绍了油孔螺塞拼接式热锻模具的设计及其应用效果。
Finally the design and application achievement of this hot forging die are described.
介绍了油孔螺塞拼接式热锻模具的设计及其应用效果。
应用推荐