Unsafe injection practices: Data show that worldwide up to 40% of injections are given with syringes and needles reused without sterilization and in some countries this proportion is as high as 70%.
不安全注射操作方面的数据表明，在全世界，反复使用未经消毒的针管和针头进行注射的比率高达40%，而且在某些国家该比例可高达70%。
We also now have a high pressure safety injection system that will inject water into the core from the refuelling water storage tank.
我们现在也有一个高压力的安全加入系统，那会将水加入到核心里去，从加料储水箱里。
This system is used to pump water into the core, low pressure safety injection and high pressure safety injection.
这个系统是用来将水抽到核心里去，降低压力安全加入和高压力，安全加入。
Unplanned power changes can result in transients, initiating ones. Then you have emergency AC power, high pressure injection systems.
无计划的动力改变能够引起瞬变，初始的，然后你们会有紧急的AC动力，高压的注入系统。
They were given high or low dose stem cell infusions, or a dummy injection.
分别为他们植入高剂量或低剂量的干细胞，或进行虚拟植入。
SQL injection attacks are a vulnerability that tend to hurt high-value sites.
SQL注入攻击是一个可能会损害高价值站点的漏洞。
When testing a high performance system, a frequent stumbling block is that of message injection.
在测试高性能系统时，常见的障碍是消息注入。
CONCLUSION: Target muscular injection of methyl cobalamin can promote the regeneration of peripheral nerve, and methyl cobalamin of high dosage can better play its role in nourishing injured nerve.
结论：靶肌肉注射甲钴胺可促进周围神经的再生，高剂量的甲钴胺可以更好地发挥其对损伤神经的营养作用。
Accurate evaluation on physicochemical property of high molecular weigh polymer is favorable for further optimization of different polymers and for guidance of injection parameters.
对超高分子聚合物理化性能的准确评价有利于对不同聚合物进一步优选并指导其注入参数的优化。
The active systems consist of several pumping systems of varying discharge pressure and flow rates, e. g., high head injection system, low head injection system.
能动系统由不同注入压力和流量的泵系统组成，如高压安注系统，低压安注系统。
Chuankezhi injection has a high similarity and stable producing technology which make it safe to be used in clinic.
喘可治注射液，他的相似度都是比较好的，他的工艺是比较稳定的，这些在临床用起来就比较放心。
Our company is a product development, mold manufacturing, plastic injection molding, electronic production of high-tech enterprises.
我公司是集产品开发，模具制造，塑胶注塑，电子生产为一体的高科技企业。
The top of the lubricator assembly includes a high-pressure grease-injection section and sealing elements.
防喷管组合的上部包括一个高压的润滑脂注入部分和密封元件。
Excessively high injection speed can cause high surface orientation and increase susceptibility to stress cracking.
过高的注塑速度会引起较高的表面方向性及增加应力破裂的敏感性。
An effective comprehensively broken down works have been implemented aimed to increasing production and decreasing pressure to the contradiction caused by dual high water injection in Erlian oilfield.
二连油田针对“双高注水”产生的一系列矛盾有效开展了以“提液降压”为主的油田综合治理工作。
Next, it puts forward a new permanent magnetism synchronous machine rotor initial point estimate method - High frequency signals injection method.
其次，探讨了一种新的永磁同步电机转子初始位置估算方法——高频电压信号注入法。
There are three parameters of fuel injection system: response pressure, injection-advanced angle, injection valve bulge high degree, the best match was found by adjusting them.
对于喷油系统参数：喷油压力、静态供油提前角和油嘴凸出高度，三个参数进行调整试验，找到它们的最佳匹配。
Using average shrinkage rates of injection-molded parts to decide the dimension of mold cavity can not satisfy the demand of high precision injection-molded parts.
采用一般的平均收缩率方法来确定模具型腔的成型尺寸，已难以满足精密注塑成型制品的精度要求。
Among the engine's features are the Twin-Scroll turbocharger and the high-pressure direct petrol injection system.
其中发动机的特点是双涡旋增压器和高压将汽油直喷系统。
There are excellent drivers with high injection rates for the RT73 chipset.
有与RT73的芯片组注射率高的优秀司机。
The larger viscoelasticity of polymer solution, the higher percolation resistance, and the greater of proportion of high injection pressure arising from elastic effect.
聚合物溶液的粘弹性越大，其在地层孔隙中的渗流阻力越大，弹性效应在增高注入压力中所占的份额也越大。
The proportion of pulverized petroleum coke injection must not be too high by comprehensive consideration of transportability and sulphur load of BF.
综合考虑输送性能及高炉所能承受的硫负荷，高炉喷吹石油焦的配比不宜过高。
The injection units are equipped with hydraulic accumulators to reach the high injection speeds and acceleration rates required for thin-walled parts.
注塑单元配备液压储能器，可实现高速注塑和加速度，适合薄壁产品。
Double tunnel junctions have been used to investigate the properties of superconducting Pb films under quasiparticle injection. At high injection level an inhomogeneous gap state was observed.
用两个重叠的铅隧道结进行实验，当注入电流很大时在铅膜中观察到了非均匀能隙态，铅膜中出现非均匀态的功率阈值比铝膜大得多。
Priority Tool Ltd is a manufacturer of high quality plastic injection moulds.
优先工具有限公司是一家以生产高品质的注塑模具。
Priority Tool Ltd is a manufacturer of high quality plastic injection moulds.
优先工具有限公司是一家以生产高品质的注塑模具。
应用推荐