A warfighter never needs to stop, put down gear and lose time in a stationary position while powering up or repacking equipment.
作战人员不需要在某个位置停下来放下装备,并花费时间重新武装。
NASA said the crew had sent down video and photographs of a small star-shaped gear with two broken teeth.Experts were trying to determine whether it was related to the problem.
NASA说乘员已经下传了有关一个断了两个齿的小型星型齿轮的视频和图像。
NASA said the crew had sent down video and photographs of a small star-shaped gear with two broken teeth. Experts were trying to determine whether it was related to the problem.
NASA说乘员已经下传了有关一个断了两个齿的小型星型齿轮的视频和图像。
I put aside my uneasiness and said, "We need to put the landing gear down now!"
我把不安放在一边,说:”我们现在需要放下起落架!“
We've also lost the nose-gear down talkback, and right-main-gear down talkback.
我们失去了前起落架和右侧主起落架的应答信号。
The thesis presents a practical die structure with Angle pin and gear shaft and rack for secondary combined inclined down loosing core of die casting hopper bodies.
本文给出了浮子室体铸件斜销-齿轴-齿条二级联合斜下抽芯压铸模实用结构,论述了模具结构特点和工作过程。
My waders and fishing gear weighed me down .
我的高筒防水靴和钓鱼工具使我不堪重负。
Then he might fly for hours on the autopilot and finally disengage it (MAYBE?) below 800 ft after the gear was down, flaps extended and on airspeed (autothrottle). Then he might bring it in to land.
然后飞机在自动驾驶仪的操控下飞几个小时,最后在800英尺以下,襟翼和起落架已经放下,由自动油门保持着速度,他解除自动驾驶操纵飞机着陆。
The device by the human operator launches, such as through the cone-shaped gear reducer drive, direct drive valve stem up and down movement of the valve gate.
本装置由人力操作手轮,通过锥形齿轮等减速传动,直接驱动阀门阀杆上下移动,启闭阀门。
The ATS616 gear-tooth sensor is a peak-detecting device that uses automatic gain control and an integrated capacitor to provide extremely accurate gear edge detection down to low operating speeds.
ATS616齿轮齿传感器是峰值侦测器件,其使用自动增益控制和集成电容器,在即便是很低的工作速度情况下也能提供相当精确的齿轮边缘检测。
The ATS616 gear-tooth sensor IC is a peak-detecting device that USES automatic gain control and an integrated capacitor to provide extremely accurate gear edge detection down to low operating speeds.
ATS616齿轮齿传感器IC是峰值侦测器件,其使用自动增益控制和集成电容器,在即便是很低的工作速度情况下也能提供相当精确的齿轮边缘检测。
So we need to keep the nose attitude all the time and need some power during touch down to transfer the weight of the airplane from the wings to the main gear.
要求我们时时刻刻保持机头的姿态,同时在接地的过程中使用小油门,让飞机的重力作用点从机翼转移到主轮。
The driver changed down from third to second (gear).
驾驶员将车速从第三挡调低到第二挡。
In a vehicle with manual transmission, you may downshift into a lower gear as you slow down.
手动档车辆,降低车速的同时,换低至合适档位。
The worm gear functions to slow down and increase torque. Its output shafts spur four-bar linkage by which the movement is changed from rotary to swinging.
蜗轮蜗杆机构的作用是减速增扭,其输出轴带动四连杆机构,通过四连杆机构把连续的旋转运动改变为左右摆动的运动。
TOWER: PH-ABC, check you have the gear down?
塔台:PH - ABC请确认你的起落架放下了吗?
We're unable to crank landing gear down.
我们无法摇下起落架。
The electric motor through the reduction gear, leads the reel rotation, causes the steel wire to wind the reel or to lay down from the reel, rises and falls the heavy item.
电动机通过减速器,带动卷筒转动,使钢丝绳绕上卷筒或从卷筒放下,以升降重物。
Change gear ratio range, in particular, using planetary transmission, the transmission ratio can be up to 100 ~ 200 (single stage), the growth rate for slow down or drive.
传动比变化范围大,特别是采用行星传动时,传动比可到100 ~ 200(单级),适用于减速或增速传动。
I would read it slowly, analyze it, read it again-perhaps changing down into an even lower gear-and then sit for 20 minutes thinking about it before moving on.
我会慢慢地读,慢慢地分析,然后再回头重读一一这次速度可能放得更慢一一之后静坐冥想20分钟,这才接着往下读。
If the worst case happens, however, and an aircraft goes down, a combat search and rescue mission kicks into high gear to extract the aircrew from hostile territory quickly and safely.
然而,如果最坏的情况出现了,有飞机被击落,一个战斗搜寻与救援的任务将火速下达,将机组乘员快速、安全地救出危险地区。
The study result can provide scientific basis for laying down management regulation on prawn drift net fishing gear in the Bobal Sea.
这项研究成果为制定渤海对虾流网渔业管理细则提供了科学依据。
The thesis presents a practical die structure with angle pin and gear shaft and rack for secondary combined inclined down loosing core of die casting hopper bodies.
本文给出了拉钩铸件弯销-斜销二级联合斜向抽芯压铸模实用结构,论述了模具分型面的确定、结构特点和工作原理。
The thesis presents a practical die structure with angle pin and gear shaft and rack for secondary combined inclined down loosing core of die casting hopper bodies.
本文给出了拉钩铸件弯销-斜销二级联合斜向抽芯压铸模实用结构,论述了模具分型面的确定、结构特点和工作原理。
应用推荐