It has been shown that finite element simulation can improve the forging process design level greatly.
从本文实例中可以看出,有限元分析方法对提高锻造工艺设计水平具有显著作用。
This study is of significance to the technological design in the compressor stator blade forging process.
该研究对压气机静子叶片锻造工艺的优化设计具有重要的指导意义。
The simulation results agree well with industrial trials, and this study could provide a good reference for forging process planning.
数值模拟与锻造试验吻合较好,为生产工艺的制定提供了有效的参考。
The whole forging process of long-axis heavy forging was divided into three steps, including squaring, stretching and chamfering-rounding.
轴类大锻件的锻造过程分为压方、拔长和倒棱滚圆三大步骤。
The proposed method can serve as the guide for optimizing the forging process and controlling the forging quality of difficult-to-deformation materials.
该方法对优化难变形材料锻造工艺和控制锻件质量具有指导作用。
Develop forging process card according to NPM plan.
依据NPM计划,及时完成锻造工艺卡片的编制工作。
Preform design is important for forging process design.
预制坯设计是锻造工艺设计中的重要内容之一。
The cold forging process of the driving gear for automobiles was analyzed.
分析了汽车驱动齿轮的冷模锻工艺。
Little allowance forging process of a new TMC -2 composite blade is studied.
研究了新型TMC -2复合材料的叶片小余量锻造工艺。
Cold forging process design is still highly based on empirical rules and experience.
整体上讲冷锻工艺流程的设计还十分依赖于经验主义的规则。
These are helpful to the forging process and heat treatment of the similar materials.
这对同类材料的锻造及热处理起借鉴和指导作用。
Shape of spiral bevel driven gear is complex and rotary forging process is also difficult.
从动螺旋伞齿轮的形状复杂,摆动辗压难度大。
The powder forging process of synchro—mesh rings for motor vehicles is described in this paper.
阐述了汽车同步器齿环粉末锻造的工艺过程。
Generous fillets and radius should be provided to aid in material flow during the forging process.
应提供尽可能大的倒角和半径以帮助材料在锻造过程中流动。
The article puts forward some viewpoints about the forging process of mine link ring based on that.
并依此对矿用连接环锻造工艺的改进提出看法。
Thrust cone has deep cavity and thin wall. Wall margin is hard to control during the forging process.
推力锥产品存在深腔、薄壁结构,锻造工艺过程中壁厚差难以控制。
The final forging process was determined as two passes roll forging and one step finish forging process.
通过模拟研究,确定该转向节的成形方案为:二道次辊锻制坯加一步终锻成形。
The hammer forging process of TC6 titanium alloy clasp has been simulated by using rigid-viscoplastic FEM.
在TC6钛合金卡环的高温锤锻过程中,模具承受非常大的应力。
The work in this paper can provide useful information for isothermal forging process of P/M superalloy turbine disk.
本文的研究结果为实现粉末高温合金盘件超塑性等温锻造奠定了基础。
The research is significant to guide how to improve the forging process design of rotors and forging quality generally.
本文的研究为全面提高转子锻造工艺设计水平和锻件质量具有指导意义。
Sheet warm forming process, sheet warm hydroforming process and sheet press forging process are introduced in this paper.
介绍了镁合金薄壁板材的温热冲压成形技术、温热液压成形技术和局部热冲锻成形技术。
Therefore it is important to study the application of microstructure models and the control of grain size in the forging process.
因此,对微观组织模型应用,锻造工艺中晶粒度的控制等方面的研究有重要意义。
Warm-hot control forging process of automobile spline shaft is investigated by using physical simulation and numerical simulation.
采用物理模拟和数值模拟相结合的手段,对汽车花键轴的温热控制精锻工艺进行了深入的研究。
The selection method of roll forging process parameters of middle tonnage automobile front axle and die design outline were stressed.
论述了中吨位汽车前轴辊锻成形工艺参数的确定方法和模具设计要点。
The article researches the effect of different hot die forging process parameters on forgings structure and properties of GH4169 alloy.
本文研究了不同热模锻工艺参数对GH4169合金锻件组织性能的影响。
The ultimate tensile strength and elongation of extrusion bar after forging process was much higher than that of the direct extrusion bar.
先锻后挤工艺棒材最终抗拉强度和断后延伸率高于直接挤压棒材。
Improper forging process will also appear large grain or uneven, hardening crack phenomenon, forging cost is higher than the casting flange.
锻造工艺不当也会出现晶粒大或不均,硬化裂纹现象,锻造成本高于铸造法兰。
Improper forging process will also appear large grain or uneven, hardening crack phenomenon, forging cost is higher than the casting flange.
锻造工艺不当也会出现晶粒大或不均,硬化裂纹现象,锻造成本高于铸造法兰。
应用推荐