• This is very helpful to choose suitable nonlinear oil film force model in the dynamic analysis for rotor-bearing systems.

    这为进行转子-轴承系统的非线性动力学分析时选取恰当的油膜力模型提供了理论指导。

    youdao

  • Establish the force model formula of drilling cuttings.

    建立了钻屑颗粒的受力模型表达式。

    youdao

  • The driving force model of elastic sleeve was established.

    建立了弹性套筒的驱动力模型。

    youdao

  • At last, the cutting force model is validated through cutting tests.

    最后,通过切削实验对切削力模型进行了验证。

    youdao

  • Rolling force model is the crucial model for process control in cold rolling.

    轧制力数学模型是冷轧工艺控制系统的中枢模型。

    youdao

  • Meanwhile, it establishes the restoring force model of special-shaped SRC columns.

    同时建立了钢骨混凝土异形截面柱的恢复力模型。

    youdao

  • The restoring force model for shear force-shear deformation in SRC joints is studied.

    研究SRC节点核心区剪力-剪切变形的恢复力模型。

    youdao

  • On the basis of theoretic analysis and experiment, the new rolling force model has been developed.

    通过理论推导和现场实验相结合,建立了新的轧制力模型。

    youdao

  • An orthogonal cutting force model with tool flank wear has been analyzed based on cutting test investigation.

    在试验研究基础上进行了有后刀面磨损的正交切削模型分析。

    youdao

  • The damping force model of the damper and the nonlinear mathematical model of vibration reduction system are established.

    建立了新型磁流体阻尼器的阻尼力模型及其减振系统的非线性数学模型。

    youdao

  • A simple milling force model for end-milling cutter is improved. The dynamic milling force and moment models are proposed.

    将一种简易的端铣刀铣削力模型改进为动态铣削力模型,并给出了铣削力矩模型。

    youdao

  • Experiment results indicate that the designed rolling force model has better adaptive capability and high prediction accuracy.

    试验研究证明,所设计模型具有良好的适应能力,提高了轧制力的预报精度。

    youdao

  • The result of on-line application indicated that rolling force model has good precision of prediction with an error less than 5%.

    现场在线应用结果表明:给出的轧制力模型具有良好的预测精度,预测误差可以控制在5%以内。

    youdao

  • Strokes sequence based rendering architecture, corresponding collision detection and virtual force model were briefly introduced.

    首先简介了基于有序笔画的汉字力觉渲染架构、快速碰撞检测算法和虚拟力模型。

    youdao

  • The method of computer aided analysis for calculating supporting force model parameters is developed, which is quick and accurate.

    研制了一种计算机辅助分析方法以计算模型中的参数,快捷而准确。

    youdao

  • The parameters in the restoring force model corresponding to the design parameters of SRC member and structure are also determined.

    建立了型钢砼结构(空腹式)的光滑恢复力模型参数与结构设计参数的关系;

    youdao

  • The calculation equations of distributed force model are derived for actuators bonded on structure by single-sided and double-sided.

    分别导出了单面粘贴驱动器和双面粘贴驱动器时的分布力模型的计算公式。

    youdao

  • This requires vast amounts of experimental data to establish a cutting force model, and requires a lot of material and human resources.

    这就需要海量的实验数据来建立起铣削力模型,这就需要耗费大量的物力和人力。

    youdao

  • Then, the damage index recording the material's behavior is integrated into restoring force model of reinforcement and concrete respectively.

    将这一记录材料性能信息的损伤指标带入材料各自的恢复力模型以考虑产生损伤后材料的强度和刚度退化。

    youdao

  • Consulting the previous research, the paper suggested the calculation method of every characteristic parameter point in restoring force model.

    参考前期研究成果提出了恢复力模型中各个特征参数点的计算方法。

    youdao

  • Based on the tests and theoretic derivation, skeleton curve of restoring force model of frame column with high axial compression ratio is got.

    在试验研究和理论推导的基础上,给出了高轴压比下框架柱恢复力模型的骨架曲线,与试验骨架曲线吻合较好。

    youdao

  • Derives limit condition equation of bridge loading capacity under damnification status on the basis of resisting force model and loading model.

    在抗力衰减模型及桥梁荷载模型的基础上,推导出了损伤状态下桥梁结构承载力极限状态方程。

    youdao

  • The damping force model of the designed ER adaptive damper is developed in detail, and the strategy of the additional damping control is proposed.

    推导了电流变可调阻尼器的力学模型,并提出了相应控制策略。

    youdao

  • Based on traditional cutting force model in face milling, a new cutting force model for the prediction of static cutting forces has been presented.

    以传统的端铣切削力模型为基础,提出了一种新的端铣加工中静态切削力的预报模型。

    youdao

  • During the sculpture surface milling machining, cutting force in ball end cutter along the tool path can be calculated according to the force model.

    雕刻表面球形铣削加工中,根据刀头的受力模型,可以计算整个刀具路径上刀头的受力。

    youdao

  • Based on traditional face milling force model, an enhanced model for complex work piece geometry which are more practical is presented in this paper.

    以传统的端铣切削力模型为基础,针对复杂加工表面形状,提出了一种更加符合实际加工情况的端铣切削力模型。

    youdao

  • The force model of the jig needle bar in the process of grinding diamonds were analyzed, and the calculation formula of grinding force was established.

    分析了宝石磨削过程中的夹具针杆的受力模型,建立了基于因次解析法的夹具针杆磨削力计算公式。

    youdao

  • The distributed force model of intelligent beam structures is presented considering the effect of bonding layer on the basis of theory of linear strain.

    以线性应变理论为基础,提出了考虑粘贴层影响的智能结构梁分布力模型。

    youdao

  • The traditional rolling force model of 4-stand tandem cold strip mill at Anshan Iron and Steel Corporation was analyzed, and some defects were found out.

    分析了鞍钢冷轧厂4机架冷连轧机轧制力模型,指出了其存在的主要缺陷,并提出了改进方案。

    youdao

  • The conventional inter-particle force model, including van der Waals force, Coulomb force and image force, could not explain these interaction behaviors.

    受力分析表明,包含范德华力、静电库仑力和电像力的传统颗粒间作用力模型不能解释这种相互作用行为。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定