稳定进料量。
The feeding rate of expanded feed is lowest.
膨化颗粒饲料的摄食率最低。
Furthermore, the quantity and feeding rate of the chlorination agent can be controlled easily.
氯化试剂的用量和进料速度都易于控制,可有效抑制环境污染。
The effect of powder feeding rate on the structure and property of a laser-clad coating was studied.
实验结果表明,随粉末送给率的增加,熔覆层厚度增加,熔覆层组织细化,熔覆层的硬度变化不大。
The width changes little with the change of powder feeding rate and the height increases with the increase of powder feeding rate.
熔覆层的宽度随送粉速率的改变变化不大;熔覆层的高度随送粉速率的增加而增加;
Moreover, keeping negative error (3% or so) of wall thickness and adopting big feeding rate are beneficial to improve the precision of spinning parts.
旋压过程中保持一定的负偏离(3%左右),同时采用较大的进给比有利于提高旋压件精度。
There are multiplicity of stable states in herbage populations owing to the influences of intraspecific mutualism, feeding rate and density of herbivores.
由于种内互助作用的存在及食植者采食速率、食植者密度等因子的影响,牧草植物种群存在多个稳定平衡点。
The effects of different compounding conditions (rotor speed and feeding rate) on the interlamellar space and mechanical properties of the composite were analyzed.
分析了不同工艺条件(主要为转子转速和喂料速率)对复合材料层间距及其力学性能的影响。
The strengthening heat transfer can significantly improve reduction feeding rate and shorten the cycle of reduction process, finally increase production efficiency.
通过强化传热可以大幅提高还原加料速度,缩短还原生产周期,提高生产效率。
The carbon conversion rate and net growth rate were positively related with feeding rate, and reached their peaks at 9.29% and 10.41% for the voluntary feeding group.
碳转化率、净生长率与摄食水平之间呈显著正相关关系,在自由摄食状态下分别达到9.29%和10.41%。
Single pass laser surface of the specimens using powder feeding method were obtained by varying the powder feeding rate and the preheating temperature of the substrate.
通过改变送粉激光熔覆过程中的扫描速度、送粉速率、基体预热温度等工艺参数,获得了单道激光熔覆层。
When the impact crusher is in operation, the device can make its workload even, feeding rate constant and smashing effects high, and will greatly enhance the production efficiency and product quality.
采用本装置,可使该机工作负荷均匀,运转平稳,进料速度一致,粉碎效果高,并能提高生产效率和产品质量。
Feeding rate, the kiln incline degree and the kiln rolling speed are adjusted to study the changes of particles mean residence time (MRT), mean volume flow (MVF) and loading rate in the kiln.
通过改变给料率、回转窑倾角、回转窑转速来考察它们对物料在回转窑内的平均停留时间(MRT)、平均体积流率(MVF)、填充率的影响。
Feeding rate, the kiln incline degree and the kiln rolling speed are adjusted to study the changes of particles mean residence time (MRT), mean volume flow (MVF) and loading rate in the kiln.
通过改变给料率、回转窑倾角、回转窑转速来考察它们对物料在回转窑内的平均停留时间(MRT)、平均体积流率(MVF)、填充率的影响。
应用推荐