Primary effects include gravity and wind - but at a secondary level, you have to think about temperature and moisture changes, the materials slightly deforming under load.
初始效应包括重力和风——但在二次效应层面上，你就得考虑气温和水分变化，材料因负重导致的轻微变形。
AZ31 magnesium alloy, one of the most widely used commercial deforming magnesium alloys, has good strength and ductility as well.
AZ 31镁合金具有良好的延展率和较高强度，是目前商业化应用最广的变形镁合金。
A numerical model, based on the finite element method, is established to describe a fluid flow in a deforming saturated oil reservoir.
利用有限元方法，建立了一个描述可变形饱和储层中流体流动的数值模型。
The epoxy bitumen is widely used in the paving of steel deck because of its good strength, anti-deforming capability and anti-fatigue performance.
环氧沥青因其良好的强度、抗变形能力和抗疲劳性能，在钢桥面铺装中应用越来越广泛。
The gear forging formation is a complicated and large plastic deforming process.
齿轮锻造成形是一个复杂的塑性大变形过程。
The angular rate matching algorithm USES two methods to estimate deforming angles.
角速度匹配算法采用两种方法对变形角进行估计。
It has developed the parametric residual deforming FEA in crankshaft rolling process.
二次开发了参数化曲轴滚压加工残余变形的有限元分析。
Meanwhile, the selection of the die material and the deforming equipment is complete.
通过对每道工序的计算，选择了对应的成型设备和模具材料。
Delayed union in 3 cases, deforming union in 2 case, posttraumatic arthritis in 5 cases.
骨折延期愈合3例，畸形愈合2例，发生创伤性关节炎5例。
Long working life and small deforming can be realized by improving anneal process and quenching process.
通过改进退火工艺和淬火工艺，获得更高使用寿命和更小的变形。
Based on the cold roll forming steel, its characteristic of roll-forming and deforming rule was analyzed.
以冷弯型钢中的槽钢为例，分析了其辊弯成型的特点及变形规律。
Metal plastic deforming process is a kind of quite complex and large elastic-plastic deformation process.
金属塑性加工的变形过程是一个非常复杂的弹塑性大变形过程。
The velocity field of deforming region was obtained from the associated flow rules for Coulomb materials.
由库仑材料相关联流动法则推得了变形破坏区的速度场。
Depending on the intensity of the deforming forces the folds may be gentle sharp overturned or overthrust.
根据变形力的强度，褶皱可以是平缓的，陡峭的，倒转的，或逆掩的。
Its basic forms are rapture and fatigue, plastic deforming, wearing, holding-on, cold and hot fatigue, etc.
模具失效的基本形式有断裂与疲劳、塑性变形、磨损、咬合、冷热疲劳等。
For matrix cracking and large deforming, the deformation of a filament wound case is analyzed and calculated.
本文分析计算了基体开裂及大变形对纤维缠绕壳体变形的影响，得到了比较满意的理论分析结果。
Transient numerical simulation for Bridgman method was carried out by means of deforming finite element method .
采用变形有限元法对坩埚下降法晶体生长过程进行了瞬态数值模拟。
The flow stress decreases with the increase of deforming temperature and increases with the increase of strain rate.
流变应力随着变形速率的增加而增加，随着变形温度的升高而降低。
The model used to control mesh deforming is improved spring analogy with boundary improvement and torsional effect improvement.
网格变形的物理模型采用改进的弹簧近似模型，改进措施包括边界修正和扭转效应修正。
The post-deforming form of tube is determined by the amplitude, pulse width, distribution and end restrain condition of pulse force.
磁脉冲力的形式（峰值、脉宽）、分布与端部约束条件决定管件变形后的形状。
It is proved in practice that gangue foundation is apt to give rise to instability to the buildings on it, due to its soft and deforming nature.
实践证明，煤矸地基为不良软土地基，工程上具有塑性、流变等不稳定现象，极易造成建筑物失稳。
Adopting this method not only can analyze instantaneous strain condition and evolution during tube bending, but also can analyze deforming feature.
采用该方法不仅可以分析弯管成形过程瞬时应变状态及其演化过程，而且可以分析弯管成形过程变形特点。
In the isothermal condition, the effect of temperature was introduced by temperature terms in evolution equations of isotropic deforming resistance.
在等温条件下，在各向同性变形阻力演化方程中引入温度项来考虑温度效应。
The invention provides a camera module, which comprises a lens base, a lens cone, an image sensor, an electro-deforming element and a control circuit.
一种相机模组包括镜座、镜筒、影像感测器、电致变形元件和控制电路。
The thinning drawing force is calculated through deforming work method and slip-line method irrespectively, and the results are compared in this paper.
本文用变形功法和滑移线法分别求解变薄拉深力，并将两种方法的计算结果进行了比较。
After analyzing and comparing the performance of normal bracing structures in mechanics, we use a freely supported beam for sensing deforming structure.
通过对常用支撑结构的力学分析与性能对比，选用简支梁作为压力传感器敏感变形机构。
The influence of deforming temperature as well as primal austenite grain sizes and holding time on the microstructure of transformation were investigated.
通过热模拟实验，考察了在不同变形温度和不同奥氏体晶粒尺寸等条件下保温对低碳钢形变后组织演变的影响。
The influence of deforming temperature as well as primal austenite grain sizes and holding time on the microstructure of transformation were investigated.
通过热模拟实验，考察了在不同变形温度和不同奥氏体晶粒尺寸等条件下保温对低碳钢形变后组织演变的影响。
应用推荐