• Under the two kinds of cutting conditions, better surface roughness can be obtained.

    两种切削条件下均可获得较理想的表面粗糙度。

    youdao

  • The normalized processing makes the setting of the threshold for alarm independent from variation of cutting conditions.

    归一化处理使报警门限设定不受切削条件变化的影响。

    youdao

  • The results obtained show that the characteristics identification of tool cutting conditions is attained by the approach.

    结果表明,该方法实现了对刀具切削状态的特征识别。

    youdao

  • The ultra high speed grinding mode may improve the cutting conditions of the grains and thus reduce the specific grinding energy.

    采用超高速磨削,对改善磨粒的切削状态,降低比磨削能是非常有利的。

    youdao

  • In the designing of Modular Machine Tool, choosing cutting conditions and calculating spindle parameters are very important tasks.

    在组合机床设计中,切削用量选择和主轴参数计算是一项非常重要的工作。

    youdao

  • The paper presents the machinability of crystal materials, and emphasizes the influence of cutting conditions on the mirror finish.

    探讨晶体材料的切削加工性,重点分析切削条件对实现镜面车削的影响。

    youdao

  • An experimental study is presented to investigate the effects of cutting conditions on kerf geometry with variable process parameters.

    采用连续改变激光切削参数的方法,研究了切割条件对切口形状和尺寸的影响及切口控制方法。

    youdao

  • Curvature and radius of curvature of central wheel are solved and non end cutting conditions of actual profile of central wheel are deduced.

    对中心轮理论廓线的曲率和曲率半径进行了解析,并由此确定中心轮实际齿廓避免顶切条件约束。

    youdao

  • The actual separation of the metal starts as a yielding or fracture, depending upon the cutting conditions, starting from the cutting tool tip.

    金属的实际分离始于屈服或断裂(视切削条件而定),从切削刀尖开始。

    youdao

  • Based on the basic principle of vibration drilling, its kinematics characteristics was analyzed and the cutting conditions of twist drill were studied.

    基于振动钻削的基本原理,对轴向振动钻削的运动学特性和钻尖切削状况进行了分析。

    youdao

  • Crack-free surface that is formed in ductile regime of glass can be obtained under conventional cutting conditions if the tool parameters are chosen properly.

    如果刀具参数选取得当,能在常规切削用量下获得在玻璃的塑性域内形成的、无微裂纹的加工表面。

    youdao

  • The analyzing method of grey relativity is used for identifying main error sources under different cutting conditions, and these results are verified by experiments.

    采用灰色关联度分析方法识别不同切削条件下的主要误差源,并进行了实验验证。

    youdao

  • The variation of the lamella width in different cutting conditions and the relation between the lamella width and the chip deformation coefficient are also analysed.

    分析不同切削条件下层片宽度的变化及其与变形系数之间的关系。

    youdao

  • In this article, the natural frequencies of machine tools under continuous cutting and steady non-continuous cutting conditions are identified with time series method.

    本文用时间序列分析的方法,在机床连续切削和非连续平稳切削状态下识别机床的固有频率。

    youdao

  • The formation of the fatigue cracks and the thermally induced cracks are mainly responsible for the failure of the ceramic tool materials under various cutting conditions.

    在不同的切削条件下,疲劳裂纹和热裂纹是造成刀具材料失效的主要原因。

    youdao

  • The formation of the fatigue cracks and the thermally induced cracks are mainly responsible for the failure of the ceramic tool materials un der various cutting conditions.

    在不同的切削条件下,疲劳裂纹和热裂是造成刀具材料失效的主要原因。

    youdao

  • This paper addresses the optimization strategy for the selection of economic cutting conditions in multipass face rough milling operations on CNC and conventional machine tools.

    研究了数控与普通铣床多次走刀端面粗铣加工中铣削用量的计算机辅助优化。

    youdao

  • Finally, the cutting conditions determination software developed for turning machining based on the above model has been put into application to show its feasibility and effectiveness.

    最后,通过基于此模型的车削加工用量选择软件的实例运行结果表明其可行性及有效性。

    youdao

  • With the help of this optimization model, the optimized drill structure, which will generate minimum radial cutting force and torque, can be determined for different cutting conditions.

    利用该优化模型对不同加工条件下的浅孔钻进行优化,得到使径向合力及扭矩为最小时的钻头结构参数。

    youdao

  • The experimental results show that cutting state resistance is an effective parameter for detecting the change of cutting conditions. As a result, the optimum heating current in elect...

    试验证明,切削状态当量电阻能有效反映切削条件的变化,通过检测其变化可实现导电加热切削加热电流的最佳控制。

    youdao

  • This article analyzes the main factors and selection of rational cutting conditions influencing the surface flatness error and other defects in sawing marble plates with diamond saw blade.

    本文分析了金刚石框锯在锯切大理石时,引起表面平面度偏差和其它缺陷的主要因素以及合理工作条件的选择。

    youdao

  • This article analyzes the main factors and selection of rational cutting conditions influencing the surface flatness error and other defects in sawing marble plates with diamond saw blade.

    本文分析了金刚石框锯在锯切大理石时,引起表面平面度偏差和其它缺陷的主要因素以及合理工作条件的选择。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定