The algorithm has less control parameters and has better flexibility.
算法具有控制参数少，灵活性好的特点。
An ECU control parameters calibration system for dual-fuel automobile was developed.
介绍了双燃料汽车ecu控制参数标定系统的设计方法。
The effect of control parameters on the rate of synchronization is further discussed.
讨论了控制参量对同步速率的影响。
Surface tension is one of the important control parameters of the ceramic squeegee oil.
表面张力的控制是陶瓷印油产品的主要控制指标之一。
It can display the set temperature, control parameters and running of circuit by the keyboard.
可通过键盘，显示电路设定目标温度、控制参数、运行等。
Through repeating test and sintering theory is analyses, the best control parameters are given.
通过反复的试验和烧结机理分析对比，给出了最佳的控制参数。
The rolling strategy is the base for presetting the process control parameters of cold tandem mill.
轧制策略是冷连轧机进行过程控制参数设定的基础。
The representation has no weight factors or control parameters, and it is geometric and affine invariant.
该表示形式中没有权因子和额外的控制参数，而且具有几何不变性、仿射不变性等良好性质。
The representation has no weight factors or control parameters, and it is geometric and affine invariant .
该方法将平面上的一段圆弧曲线表示为参数复有理函数的形式。
The regression orthogonal test approach can be used to optimize the control parameters for nonlinear systems.
提出了一种优化非线性系统控制参数的方法——回归正交试验法。
The effect of waveform control parameters on weld appearance was analyzed, and the parameters were optimized.
探讨了波控参数对焊缝成形的影响，并通过大量试验对波控参数进行优化。
But the contact stability conditions impose some limitations on the impedance control parameters and the feedrate.
但是某些联系的稳定性条件的限制控制参数的阻抗和刀具。
Construction foundation, control principle and control parameters' selections of CSF control method are presented.
文中给出了CSF控制方法的构建依据、控制原理以及控制参数的选择技巧。
Among the methods of on-line optimization of basic control parameters, global optimization is an advanced technology.
针对一定的测试规范进行控制参数的全局优化是一种先进的思想。
Phased array radar detection range depends on radar technical parameters and radar operation mode control parameters.
相控阵雷达作用距离决定于雷达技术参数与雷达工作方式的控制参数。
The main tuning methods of PID control parameters based on gain margins and phase margins are summarized and analyzed.
综述并分析了基于幅值裕度和相位裕度的PID控制器参数整定方法。
Input signal of controller is solenoid valve lift. Control parameters are valve opening timing and valve open duration.
控制器的输入信号为电磁阀升程，控制量是气门开启定时和开启持续时间。
According to the practice and experience, the control rules of fuzzy controller and its control parameters are determined.
根据实际情况和操作经验，总结出模糊制器的控制规则并确定了其相应控制参数。
The relationship between control parameter and synchronization speed was analyzed by setting different control parameters.
通过设定不同的控制参量，分析了控制参量和同步速度之间的关系。
BP neural networks with pattern extended input are used to estimate control parameters, and the learning speed is increased.
并采用具有模式增强输入的BP网络进行决策参数估计，加快学习的收敛。
The retrofit kit uses a series of control parameters to determine the maximum allowable G-force loading and safe operating limits.
改造软件包中有一系列的参数确定最大允许重力负载和安全操作行程。
This paper briefly introduces the superiority, limitation, basic working principles and control parameters of actuated signal control.
介绍交叉口感应信号控制的优越性和局限性、基本工作原理以及控制参数。
The method can obtain a faster update law of unknown parameters and a faster synchronization response rate by increasing control parameters.
该方法通过增大控制参数的数值，可以得到更快的参数自适应律和同步响应速度。
According to the signals of arc voltage errors and arc state, four control regulations and counting measure of control parameters are designed.
根据电弧电压偏差信号及电弧状态，设计了四个控制规则及其控制参数的计算方法。
The deep analysis and discussion were made about performance rule of this turbine. The designing methods of the control parameters were presented.
提出了对水斗式水轮机宏观控制参数的设计思想，并对水斗式水轮机性能和规律进行了分析探讨。
The advanced software allows the student to change the control parameters, record results and analyze the results of the difference configurations.
所开发的控制软件允许学生修改控制方案和控制参数，通过记录结果分析不同的控制组态方案的实验结果。
With the application of computer control various kinds control computations and correction and optimization of control parameters are easily implemented.
采用计算机控制，便于实现各种控制算法和控制参数的修正及优化。
With the application of computer control various kinds control computations and correction and optimization of control parameters are easily implemented.
采用计算机控制，便于实现各种控制算法和控制参数的修正及优化。
应用推荐