Finalization of the relevant programs and Protection of the secondary circuit program.
最后确定相关的保护方案和二次回路方案。
Theoretical calculations showed that bidirectional loop redundancy program can improve the data transmission reliability by about 1.7 times compared with unidirectional open circuit program.
理论计算表明，该方案比单向开路方案的数据传输可靠性提高了约1.7倍。
Design a data collection module with serial port based on microcontroller. The thesis explains the circuit principle and program designing in detail.
设计了一个串口通讯的单片机数据采集模块，文中详细阐述了模块的电路原理和程序设计。
This paper detailedly introduces the whole design scheme of the system, the circuit on interface module and 89c51, the method of the software design and program flow chart.
详细阐述了系统的总体设计方案，给出了界面模块与89c51接口电路，最后介绍了软件设计方法及程序流程图。
The design of hardware circuit is explicated and the diagram of program is offered.
详细描述了硬件电路的设计，并给出了软件程序框图。
The host program takes on the complex computational tasks such as parameter adjusting and the waveform data subdividing, which simplifies the circuit for the peripheral unit.
将参数调整，波形数据细分的复杂计算任务交于主机程序完成，简化了外设执行部件的电路结构。
This paper puts forward a method of designing fluid logic circuit according to program characteristics and productive conditions.
本文提出从程序特征及生产条件出发选用流体逻辑回路设计方法。
The characteristics and operating principle of DS3070W are introduced, the typical application circuit with AT89C51 and software program code are given.
介绍了DS3070W的性能特点及工作原理，给出了它与AT 89c51的典型应用电路及子程序。
In the software aspect, it curtly introduces flow chart of main program and the programming method of all ports of circuit.
在软件方面，介绍了主程序的流程图及各部分电路的编程方法。
Lastly, the hardware circuit, VHDL program design and debugging methods based on FPGA are discussed.
最后对基于现场可编程门阵列(FPGA)的硬件电路、VHDL语言程序设计及调试方法进行了讨论。
PID regulation in instrumentation circuit is realized by using program logic controller.
利用可编程序控制器实现仪表回路的PID调节控制。
Introduces the circuit, program flow and operation sequence of the serial-scan mode static locking display.
介绍一种串行扫描方式静态锁存显示的电路、程序流程和工作时序。
The simulation with PSPICE program proved that the designed circuit has ideal character of Schmitt circuits.
用PSPICE程序模拟证明了所设计的电路具有理想的施密特电路特性。
The design principle and circuit construction and program process of apparatus of the best ignition angle for motorcycle engine are introduced.
介绍了一种摩托车发动机最佳点火角试验仪的设计原理、电路结构和程序流程。
Adding the watchdog circuit, the system can avoid program operation confusion and assure the system operation normal.
看门狗电路的加入，使系统避免程序运行混乱，保证系统正常工作。
This paper introduces the work principle, components of hardware circuit and relative program flow of the control.
这里介绍了这种控制器的工作原理、硬件电路组成及有关的程序流程。
The article also introduces design process, circuit and program structure.
给出了较详细的设计过程、电路和程序结构。
An introduction to the circuit structure and program of universal CAN node as well as the application in inductive heating.
介绍一种通用CAN节点的电路结构、相关应用程序及在工业中频感应加热设备控制现场总线中的应用。
In real time control system, it is important to design the clock control circuit and program.
在实时控制系统中，时钟控制电路及程序的设计十分重要。
Exponentially increasing of the state number of a system causes the combination exploring with the scale of program or circuit increasing.
随着程序或电路规模的增大，状态数目将呈指数增加而引起组合爆炸。
The theory, the circuit, and the program were introduced using LM567 as the component to detect the ultrasonic and using the MCU 89C51 as the main control component.
介绍了用集成锁相环路解码器LM567作为超声波检测元件，以89C51单片机作为主控元件的超声波液位测量的原理、电路及测控程序。
Explicated the structure and principle of work of ultrasonic launching and receiving circuit, presented the program frame and part program of the date processing.
并对超声波发射接收电路的硬件结构和工作原理做了较详细的说明，给出了数据处理系统程序框图和部分程序。
This paper introduces the application of HH204 stepping motor's driver on multi-rate register, presents a circuit and driver program.
介绍HH204步进电机驱动电路在复费率计度器上的应用，给出了硬件电路和驱动程序。
The paper simply introduces the evacuation system for model H-600 electron microscope and analyzes the program of evacuation and the program control circuit.
文章简要介绍了日立h- 600型电子显微镜抽真空系统，分析了抽真空程序及其程序控制电路。
Playback apparatus, playback authorization server, program, and system integrated circuit.
播放设备，播放授权服务器，程序，以及系统集成电路。
This article mainly deals with the designs of hardware circuit and software program of frequency transformer by DSP.
本文采用DSP进行变频控制器的硬件电路设计及软件程序设计。
Two kinds of program control signal attenuation circuits, which are used in circuit design, are introduced.
本文介绍线路设计中所应用的两种程控信号衰减电路。
A simple equivalent circuit model of quantum well laser (QW LD) which is derived by QW rate equations and is accomplished in the circuit simulation program SPICE.
给出一个新的量子阱激光器等效电路模型，由量子阱激光器单模速率方程推导得到并在电路模拟程序SPICE中完成。
The part key circuit and software program block are given.
给出了部分关键电路连线图及软件程序模块。
The system consists of driving pulse generating circuit for CCD, instrumental amplifier with low noise, MCU controlling circuit and PC program for dealing with the data conveyed by MCU.
系统包括CCD驱动脉冲产生电路、低噪声测量放大电路、自适应比较电路、单片机控制电路以及上位机处理程序。
应用推荐