Graduate tuition differs by program.
研究生的学费因课程而异。
Can be imported by program files or by other definition files.
可由程序文件或其他定义文件导入。
Since the file EMPADDRESS is being handled by program UPDHANDLER, then the UPDATE operation is processed as described earlier in Figure 5.
由于文件EMPADDRESS 正在被程序UPDHANDLER 处理,因此UPDATE操作按照此前图 5中描述的方法处理。
Sensors are triggered or stopped by software set and maximum of range reading is also set by program.
超声波传感器的启动和停止、最大测量距离可以通过软件编程在线调整。
Double coordinate gang wire has added U. V. two drive motors to carry out taper cutting by program control.
双坐标联动丝架是在丝架上增加了U、V两个驱动电机,通过程序控制来实现锥度切割。
Events can be generated by a user action, such as clicking the mouse or pressing a key; by program code; or by the system.
事件可由用户操作(如单击鼠标或按某个键)、程序代码或系统生成。
Automatic mesh generation with optimization and bandwidth reduction by program will observably improve the efficiency and make the analysis result more reliable.
编制程序,实现了有限元网格的自动生成以及网格和带宽的优化,提高了分析的效率和可靠性。
Roundness error is evaluated by minimum region law. The diameter of the holes and the distance between the axes of two holes are calculated and measured by program.
在测量尺寸时,依据图像分割所提取的轮廓,使用自编程序利用最小区域法对圆度误差进行评定,并计算、测量链板的孔径和节距。
This method decreases the number and values of error factors, improves the test accuracy and efficiency, also makes the calibration procedure be performed automatically by program.
该方法减少了误差因素,提高了测试精度,而且使在轨测试系统的校准由程序自动执行,提高了测试效率。
Based on the theory of the unsteady temperature field and stress field, three-dimensional finite element model is set up. The wall is analyzed by program of ANSYS finite element analysis.
本文根据瞬态温度场和应力场理论,建立地下室混凝土墙体的三维有限元分析模型,利用有限元分析程序ANSYS对基本工况下的墙体进行分析。
By use of the processing method described in this paper, the general information on machinery design can be processed to become a form which can be called by program or inquired by computer.
借助本文介绍的处理方法,可对常用的机械设计资料进行加工处理,使之成为程序可调用或计算机可检索查询的形式。
Some key technologies on hardware programming control such as GPIB communication technology, 8255A chip'scontrolling by program, step-motor's driving technology, are also introduced in paper.
论文还对系统各部分硬件编程控制的关键技术进行了介绍,如GPIB通讯技术、8255A的编程控制、步进电机驱动技术等。
The realization of automatic edge matching by program can not only avoid the carelessness of manual working, but also find the edge matching errors which are difficult to find by manual working.
由程序实现的自动接边检查不但可以避免人工作业的疏漏,而且对于某些人工作业难以发现的错误,也有较好的效果。
The setting of welding parameters, involving stud lifting height, stud sending depth, lifting and sending speed and so on, can be accomplished by program control, thus the artificial error is reduced.
螺柱提起高度、送下深度、提起和送下速度等焊接参数的设定由程序控制,减少了人工调整的随机误差;
The setting of welding parameters, involving stud lifting height, stud sending depth, lifting and sending speed and so on, can be accomplished by program control, thus the artificial error is reduced.
螺柱提起高度、送下深度、提起和送下速度等焊接参数的设定由程序控制,减少了人工调整的随机误差;
应用推荐