这种测量工具用以测量奇数齿齿轮的齿顶圆和齿根圆直径。
The measuring instrument can measure addendum circle and dedendum circle diameter of odd-tooth gears.
介绍了齿顶整圆弧滚刀的应用和设计。
This paper introduces application and design of full radius hob on tooth tip.
它是外花键的齿根圆,和内花键的内圆(齿顶圆)。
It is the root circle of the external spline or the inside circle (tooth tip circle) of the internal spline.
它是外花键的外圆(齿顶圆),和内花键的齿根圆。
It is the outside circle (tooth tip circle) of the external spline or the root circle of the internal spline.
模拟结果显示,工艺改进后,花键上方齿顶成形饱满。
The results show that the new process achieves synchronizer ring with full teeth.
齿形的几何计算可避免内齿圈齿顶与行星轮齿根发生干涉。
Gear shape is calculated and interference of planetary gear dedendum and internal gear addendum is avoided.
应用齿顶整圆弧滚刀是提高齿轮弯曲疲劳强度的有效措施之一。
Full radius hob on tooth tip is one of the effective measures by increasing gear tooth bending strength.
分析了滚刀齿高和齿顶倒圆半径对所切齿轮齿根弯曲应力的影响。
And it analyzed that hob tooth height and tooth top pour round radius impacted on gear tooth root crooked stress.
直接驱动数控转台;不等齿顶宽;双转子;移相技术;重复控制。
Direct Drive NC Table; Unequal Teeth Tips Width; Dual-Rotor; Phase Shifting; Repetitive Control.
当前,齿顶整圆弧滚刀广泛应用于重型汽车变速器齿轮的生产中。
At present, full radius hob is used extensively for heavy transmission gear production.
指出通过计算作出图形,可分析出滚刀齿顶圆弧的设计是否合理。
It pointed out that the design of gear cutter should greatly increase the tooth point arc so as to reduce the stress concentration to increase the force of tooth root.
在单齿圈破岩试验中,理想的岩样是与牙齿齿顶线相贴合的锥面岩样。
The ideal rock sample is the conical surface rock sample that can joint crest of teeth in single row drilling experiment.
提出了一种改进榨辊齿形并在齿顶弧面上堆焊碳化钨的方法及其加工工艺。
A method to improve the tooth shape of mill roller and adopt the built - up-welding with tungsten carbide on the curved surface of tooth apex has been introduced.
因此,在齿面非正常接触导致齿顶接触应力过大的情况下,该齿轮发生了早期疲劳剥落。
Due to the above mentioned defects, early fatigue peeling occurs under the condition of overly contact stress at the top of the tooth caused by abnormal contact at the tooth surface.
齿顶高系数是设计齿轮时的重要几何参数,也是影响复合齿轮泵流量特性的重要参数之一。
The addendum coefficient is an important parameter in the designing the gear, and to affect the discharge characteristic of compound gear pump.
在渐开线少齿差行星传动中通常使用短齿,其齿根高与正常齿相同,而齿顶高小于正常齿。
The stub gear tooth is often adopted in the involute planetary gear transmission with a few tooth number difference.
测量齿顶圆直径估算分度圆螺旋角,用分度头在铣床上修正分度圆螺旋角,并进行误差分析。
The spiral angle of graduated circle was rough estimated by measuring the addendum circle diameter and modified on milling machine.
分析了标准和齿顶修形渐开线齿轮的轮齿本体温度和瞬时接触温度及相关因素对它们的影响。
Factors influencing the tooth bulk temperature and the surface transient contact temperature of involute gears with standard and modified tooth profiles are investigated.
按常规方法设计的大压力角渐开线花键插齿刀,常出现刀具齿顶宽太小和齿根槽太窄的问题。
According to the normal design method the former involute spline gear shaper cutter often has different size of its tooth top and tooth root.
文摘:设计了一种测量工具,用以测量奇数齿齿轮的齿顶圆和齿根圆直径,以便确定齿轮的主要参数。
Abstract: this paper designs a measuring instrument which can measure addendum circle and dedendum circle diameter of odd_tooth gears and can define all main parameters of gears.
渐开线终止圆与齿顶圆(或者修缘线的起点所在的圆)共同限制了所要求控制的渐开线齿廓的范围。
This circle along with the tooth tip circle (or start of chamfer circle) determines the limits of tooth profile requiring control.
细高齿齿轮是采用小模数、小压力角、大齿顶高来加大端面重合度,达到提高齿轮强度、降低噪声的目的。
High tooth gear has small module, small pressure Angle, and large addendum to enlarge the transverse contact ratio, improve gear strength, and reduce the noise.
传动部分是渐开线齿轮,工作部分可采用不同的工作面,如圆柱外圆面或圆弧形齿或渐开线齿轮齿顶修圆。
The transmission part is an involute gear, and the working part can adopt different working faces, such as a cylinder excircle face, a circular arc tooth or an involutes tooth gear top cavetto.
并就刺针刺辊对纤维损伤小的机理进行了分析,提出齿条刺辊齿顶齿宽远大于刺针针尖直径,可能是齿条对纤维损伤较大的原因之一。
The analysis is done to the mechanism of the less damage of the pricker roller. Conclusion is made that the tooth width of the wire may be the cause of the more damage of the wire roller.
本文阐述了渐开线直齿圆柱齿轮顶圆直径及齿轮模数、变位系数和压力角等参数的确定方法和步骤。
The method and procedure of measuring and calculating involute spur gear geometrical parameters such as tip diameter, module, modification coefficient and pressure Angle were shown in this paper.
经现场使用试验证明,本研究所制备的具有梯度结构的硬质合金顶锤、涂层刀片以及硬质合金钻齿的使用性能均明显优于常规均匀结构的硬质合金。
Practical tests show that the performance of cemented carbide anvils, coated blade and drill bits with graded structure developed in this dissertation are superior to those with regular structure.
另一手用准备好的餐巾顶啤酒瓶盖。可以有效的利用瓶盖下的“齿”纹。
Take the napkin and press it hard against the bottle cap. Try to catch one or two of the "teeth" under the bottle cap.
对中心轮理论廓线的曲率和曲率半径进行了解析,并由此确定中心轮实际齿廓避免顶切条件约束。
Curvature and radius of curvature of central wheel are solved and non end cutting conditions of actual profile of central wheel are deduced.
结果表明,牙顶处金属材料受到丝锥棱齿的压力相对较小,并且金属流向牙顶两侧上方的区域时受到的阻力最小;
Through metallographic analysis of the material, microstructure change and deformation mechanism of crest, flank and root of the thread along the layer depth direction were obtained.
结果表明,牙顶处金属材料受到丝锥棱齿的压力相对较小,并且金属流向牙顶两侧上方的区域时受到的阻力最小;
Through metallographic analysis of the material, microstructure change and deformation mechanism of crest, flank and root of the thread along the layer depth direction were obtained.
应用推荐