第五章详细阐述了网络回放流媒体通信软件的设计实现。
Chapter5 presents the network playback stream media communication software design in detail.
第四章详细阐述了实时流媒体网络通信软件的设计实现。
Chapter4 presents the realtime stream media network communication software design in detail.
介绍了一种远程集中抄表系统的设计原理和系统组成，并详述了系统通信软件的设计。
The design principle and constitution of remote concentrated ammeter reading system is presented, the design of its communication software is described.
文中还叙述了DDM系统内各处理单元连接的硬件实现方法、工作原理以及通信软件的设计。
This paper describes the implementation of interconnection among processing units in DDM and the design of communication software.
本文介绍了系统的硬件结构，嵌入式通信软件的设计，嵌入系统中远程数据文件传输的实现方法。
The data from embedded system were transmited to the server through Internet by file transfer protocol.
重点针对试验指挥监控的特点，研究了通信与控制协议、监控软件和通信软件的设计方法和实现途径。
Aim at the characteristic of test command control, designing methods of the communication protocol, control software and communications software war was studied.
本文的主要研究工作是基于DECT的通信软件的设计与实现，实现了以满足语音通话和其他数据通讯需求的软硬件整体方案。
Based on the design and realization of DECT, the paper studies of the whole-set software and hardware design to fulfill the requirement of audio telecommunication and other data communication.
文中详细给出了数据采集系统的设计，基于MATLAB仪器控制工具箱的数据通信软件的设计，以及MATLAB下波形显示程序的设计。
This paper describes detailedly the designs of the data-acquisition system, the communication software based on MATLAB's Instrument Control Toolbox, and the waveform-display software under MATLAB.
文中对监控系统的硬件结构、通信协议、信息编码方案及通信软件的设计进行了详细的阐述，并从理论上讨论了信息编码方案的差错控制性能。
The hardware construction, communication protocol, signal coding schemes and the communication software are described in detail, and the performance of the error control schemes is analyzed in theory.
在进入IBM软件集团成为体系结构和工具开发的副总裁之前，他致力于远程通信技术、人工智能、程序设计语言和软件技术。
Before moving into IBM software Group to become VP of architecture and tools development, he worked in telecommunications, artificial intelligence, programming languages, and software technology.
通过设计通信和后台管理软件，以及模拟前端门禁控制器程序，实现了网络集中与分布式智能化的管理。
By designing the communication and back-end management software and simulated entrance guard controller program, we realized the centralized and distributed intelligent management.
然后，介绍了上位机软件设计以及上位机与温度记录仪之间的通信协议设计。
And then, the design of software in PC and communication protocol between PC and temperature logger are introduced.
该软件在实际加油站中的成功应用说明了该设计方案的合理性，因此对其余串口通信应用领域具有很好的参考价值。
The successful application of the software in practical oil station shows the scheme is reasonable. So, there is good value to other serial communication fields.
最后重点介绍了负荷终端无线通信功能的软件设计过程，提出了解决若干难点问题的方法。
Finally it focus on the software design process of the wireless communication of load terminal, and put forward Suggestions to solve some difficult problems.
论述了基于SJA1000的CAN总线的硬件接口电路的设计、芯片的选择、软件设计及CAN通信的实现。
The design of CAN bus hardware interface circuit based on SJA1000, the selection of chips, the design of software and the realization of CAN communication are expatiated.
介绍了一种点对多点无线数据传输系统的设计，提出了一种基于时分多址的“随机延时”防通信碰撞协议，并给出了该防碰撞协议和相关CRC编码的软件实现方法。
The design of a point-to-points wireless data traffic system is presented, including a random delay anti-collision protocol, the implementation of this protocol and CRC coding by software.
以软件工程的结构化设计方法为主线，以通信电源网络测控系统为具体的实例，成功的完成了整个系统的软件开发工作。
Construct design methodology of software engineering is main center, and communication power network monitor and control system is concrete instance.
文章的设计主要着重于通信协议的设计和软件的实现。
The paper focuses on the design of the communication protocol and the software.
本文介绍usb接口的485设备通信板卡和485设备检测软件的设计过程。
This article introduces the process of designing the communication board between 485 - bus and USB and 485-device detection system.
其中，着重对该仪器软件系统的设计和数据串行通信机制进行了分析和研究。
It puts emphasis on the design of instrument's software system and the mechanism of data's serial communication.
阐述了双CAN通信构件的设计机理，硬件构成，软件设计。
The design mechanism, hardware and software of double CAN communication were described in detail.
文章对该系统的组成，通信软件和图形软件的设计与实现方法进行了分析，并指出了今后需要进一步做的工作。
In this paper, the system's composition, design and implementation of the communication and graphic softwares is introduced, and further required research is also pointed out.
并对软件设计原则、多任务设计、数据通信、双机容错和故障诊断与处理作了较详细的讨论。
The principle of housekeeping software design, multi-task design, data communication, double computer fault diagnosing and processing are described in detail.
主要讨论了通信网络的拓扑结构、通信链路控制及通信软件设计等问题。
Topology construction of communication network, line control of communication and the software design are mainly discussed.
本文完成的工作包括嵌入式实时图像网络传输及无线通信系统的硬件设计与软件开发。
This paper presents a process of the "Network transfer of Real-time Video and Wireless Communication System", including hardware design and software development.
本文的重点是无线点菜机的硬件设计和软件移植以及无线通信等关键技术的实现。
The key techniques of this thesis are hardware design and software porting of wireless handheld unit and the realization of wireless communication.
本文的重点是无线点菜机的硬件设计和软件移植以及无线通信等关键技术的实现。
The key techniques of this thesis are hardware design and software porting of wireless handheld unit and the realization of wireless communication.
应用推荐