针对飞机叶片表面变形量测量要求提出一种非接触式光学测量方法。
This paper presents an untouched optical measuring method in finding out the deformation of an aircraft engine vane.
根据接触载荷数据,可计算得到接触载荷与样品表面变形的关系。
Based on the achieved contact force data, the relation of the contact force and deformation depth of specimens can be obtained by calculation.
在电弧与熔池统一模型的基础上研究熔池上表面变形对电弧行为特征的影响。
This paper studied the effects of weld pool surface deformation on welding arc behavior characters basing on unified arc pool mathematical model.
因此在边坡变形监测中采用边坡内部测斜为主,表面变形监测为辅的监测方案是合理的。
Therefore, it is proper for this project to monitor slope deformation byinclinometers, while the surface displacement survey can be used as a supplement.
本文对表面微观屈服应力的测量与计算方法及表面变形的应力应变曲线进行了分析研究。
The calculation of micro-yield stress in surface layer and the stress-strain curves of surface layer deformation were studied.
根据流体力学理论和变分法原理,推导出了熔透情况下TIG焊接熔池上表面和下表面变形的方程。
The calculating formulas of top and bottom pool-surface deformation in TIG full-penetration weld pool is developed based on principles of fluid mechanics and variation calculus.
分析结果表明,配油盘的强度满足设计要求,但配油盘表面变形较大,远远超过配油盘的平面度要求。
The results show that the plate strength meets design requirement. The plate surface distortion however, exceeds flatness specification.
利用粒子图像测速仪(PIV)对圆筒形容器内有自由表面变形的粘弹性流体旋转流动进行了实验研究。
By using a particle image velocimetry (PIV), an experimental study was performed on the swirling flow of viscoelastic fluid with deformed free surface in a cylindrical container.
磨粒侵入方向不仅影响材料表面变形、表面接触压力和表层应力的大小,而且会引起压力和应力分布形状的改变。
Particle penetrating direction has influences on the magnitude of surface deformation, contact pressure and stress, and the distribution forms of contact pressure and stress.
一旦接触土壤表面,这条“鼻涕虫”就会发生另一种变形。
Once it reaches the surface of the soil, the "slug" undergoes another transformation.
在金属压力加工中,利用电塑性效应可降低金属变形抗力,增加金属成型极限,改善产品表面质量。
Electroplastic effect can be employed to increase metal forming limit, reduce deformation resistance and improve surface quality of product.
所有的翻修表面在去除腐蚀、受热和变形材料后必须进行喷丸。
All reworked surfaces must be shot-peened after removing material damaged by corrosion, heat, and deformation.
纳米级的磨粒冲击到工件表面,在以原子级去除的同时伴随着塑性变形的发生。
When abrasive grains impacted on the work piece surface, the top layer atomics are removed, plastic deformation appears at the same time.
在表面失稳以前,半无限体的变形是有限的。
The deformation of the half space is finite before the surface buckling occurs.
后热处理可改善变形和表面应力状态、细化组织、提高硬度。
The post treatment can improve deformation and surface stress state, refine microstructure and increase hardness of cladding layer.
加载变形过程中,样品表面形成的马氏体和晶粒状浮雕具有可逆性。
The formation of granular relief and martensite on the specimen surface seems to be reversible during deformation under loading.
分析了弹性变形、表面粗糙度对润滑性能的影响,并提出了开槽环的设想。
We analyse the influence of the elastic deformation and the surface roughness for lubricating characteristics and give a thought of cutting groove in piston ring.
经渗碳及淬火后,具有表面硬度高、心部韧性好的特点、冷变形塑性中等,切削加工性好。
Carburizing and quenching, with high surface hardness, good toughness characteristics, the heart of cold plastic deformation of medium, cutting is good.
分析了表面处理方法、冷变形、扩散退火温度和时间等工艺因素对界面结合强度的影响;
The influences of process parameters include surface preparation method, cold deformation, diffusion temperature and time.
这类板的横向剪切变形效应必须予以考虑,因而层板不同层的表面法线的转角是不同的。
The effect of transverse shear deformation is considered and Angle of rotation of surface normal for each layer is different.
实木复合门:主要是实木做骨架,表面贴高级木皮做的门,造型一般非常美观,价格合理,主要的优点是不变形,不开裂。
Solid mu fu closes the door: mainly is real wood frame, make the top surface veneer, modelling generally do very beautiful, the price is reasonable, the main advantage is not deformation, no crack.
对无镍奥氏体不锈钢经塑性变形后自由表面微观形态变化以及对耐腐蚀性能的影响进行了观察分析。
The micromorphic change of free surface and property of corrosion resistance were observed after austenitic stainless steel was treated by plastic deformation.
文章根据马路坪矿深部软岩巷道表面位移的实测结果,分析了巷道围岩变形主要特征。
Based on the measured results of the displacement of deep soft rock roadway in MaLuPing mine, the deformation characteristic of the surrounding rock is analyzed.
在滚压加工工艺中,滚压套的压下量大小决定了滚压力的大小并决定了细长轴表面发生弹塑性变形的状况,从而决定了细长轴的加工质量。
In the process of rolling, the movement of rolling sets decide the rolling pressure, the deformation of the spindly shaft and consequently the rolling quality.
光固化原型制作过程中存在的主要问题是变形和表面台阶效应。
Major problems of Rapid Prototyping(RP) in StereoLithography(SL) were deformation and overall joint effect.
通过对试验结果的分析,获得加载频率和表面形态对节理闭合变形性质的影响规律。
Based on the analysis of test results, the effect of both the surface topography and loading frequency on the joint closure behavior is discussed.
考虑瞬时啮合刚度的影响,对轮齿表面的塑性变形进行了仿真计算,模拟结果与实验结果有较好的一致性。
Simulation of plastic deformation in gear tooth is implemented in consideration of mesh stiffness, which is fundamentally identical to the results from experiments.
结果表明,当焊接工艺参数合适时,可以获得表面成形良好、无变形的铝合金与钢的对接接头和搭接接头。
The results shown that a deformation-free joint with good weld surface appearance can be obtained with suitable welding conditions for butt-joint and lap-joint of the dissimilar materials.
分析了离心自毁机构套座锥面和击发体表面的变形对自毁性能的影响。
This paper analyzes the effect of the deformation of the conical surface of the sleeve and surface of the percussion body in a centrifugal self destroying device upon self destroying performance.
分析了离心自毁机构套座锥面和击发体表面的变形对自毁性能的影响。
This paper analyzes the effect of the deformation of the conical surface of the sleeve and surface of the percussion body in a centrifugal self destroying device upon self destroying performance.
应用推荐