检查螺旋桨轴与螺旋桨锥度接触面。
Check for surface contact area (metallic contact) between stern shaft and propeller hub tapers.
螺旋桨轴(中间轴)机加工尺寸检查。
Inspection machining dimension of propeller shaft (intermediate shaft or counter shaft).
螺旋桨轴上的螺旋桨位于所述舵桨壳体的外部。
The propeller on the propeller shaft is located outside the rudder propeller housing.
螺旋桨轴频是被动声纳极其重要的目标识别特征之一。
The propeller shaft frequency is one of the important target recognition features for passive sonar.
这些驱动器,中央螺旋桨轴通过减少锥齿轮2:1减少。
These drive the central propeller shaft through bevel reduction gears with a 2:1 reduction.
本文还讨论了由于螺旋桨轴数目不同而产生的重量以及功率分配的影响。
The influence of number of shafts on weight and power distribution is discussed.
螺旋桨通过使用船厂提供的液压顶升装置压入螺旋桨轴并采用湿式无键固定法紧固。
The propeller is to be force fitted to the propeller shaft by using the hydraulic jack which the Builder possess and secured by wet type keyless fitting method.
首先是舰船辐射噪声特征量的提取,包括舰船总声源级的估计和螺旋桨轴频线谱的提取。
The first part is about the features extraction, including the estimation of source level of the ship-radiated noise and the line extraction of the rotation frequency of propeller noise spectrum.
这样就避免了使用传统的螺旋轴,将螺旋桨置于干净的水流中,从而大大提高了效率。
This avoids the use of a traditional propeller shaft and puts the propellers in a clear flow of water, which greatly improves efficiency.
下水后中间轴和螺旋桨连接后校中。
Aligning intermediate shaft and propeller shaft after launching.
目标的螺旋桨不同则轴频不相同。
全系列产品均可以匹配齿轮箱销售,部分机型可以连带尾轴,螺旋桨销售。
All Marine engines could be sold with gearbox, and some engines could be sold with tail shaft and propeller.
某舰的螺旋桨尾轴长期处在恒定载荷作用下,虽然尾轴应力在弹性极限范围内,但是尾轴局部还是很容易发生微量的塑性变形。
Tiny deformation will appear in the local of the propeller shaft of certain ship which is endured an invariableness load, although the shaft stress is within the elastic limit range.
当螺旋桨要求的功率过高以至于轴转速达不到额定值时,可以采用切割螺旋桨叶梢的方法减小螺旋桨的负荷。
When the power required by propeller is so high that the shaft speed cann't arrive a rated value, the tip of propeller can be cut to decrease its load.
螺旋桨五轴数控加工技术作为一种先进的加工方法,在国外已经广泛应用而在国内的应用水平较低。
As an advanced nc machining technology, five-axis machining for propeller is widely used abroad but limited in domestic.
“高速”型的现代水平轴风力涡轮机,如用于大规模发电的那种,一般包括两个或三个直径为100米或更大的螺旋桨式叶片。
Modern horizontal axis wind turbines of the "high-speed" type, as used in large scale power generation, typically include two or three propeller-style blades with a diameter of 100 meters or more.
所以对螺旋桨尾轴进行蠕变分析是十分有意义的。
So it is significative to carry out a research on room temperature creep characteristic of propeller shaft .
螺旋桨是螺纹在轴上,而当安装之间的磁石的著磁,沉重的刀片将降至底部。
The propeller is threaded over the shaft, and when mounted between the magnets, the heavy blade will drop to the bottom.
一种空气过滤机,它涉及炭(9)的吸附技术,转动轴(4)穿过输气管(13)与螺旋桨(2)相连。
The utility model discloses an air filter, which relates to the absorption technology of charcoal (9), a rotation shaft (4) is connected with a propeller (2) through a gas pipe (13);
有一螺旋桨,置于圆拱形罩体的下方并与动力舵机的轴连接。
A propeller is arranged at the lower part of cover body in a circular arch shape and is connected with the motive power steering engine in a shaft connection.
本文提出的变磁阻式螺旋桨动力仪除用于水面船模试验外,并可用于水下模型及多桨轴模型试验。
The R. P. D. is presented in this paper. Except the usual ship model test, it is possible to carry out measurement of tests for the underwater model and multi-propeller shaft model.
本文提出的变磁阻式螺旋桨动力仪除用于水面船模试验外,并可用于水下模型及多桨轴模型试验。
The R. P. D. is presented in this paper. Except the usual ship model test, it is possible to carry out measurement of tests for the underwater model and multi-propeller shaft model.
应用推荐