薄壁件往复运动的动力来源是曲柄传动机构(2)。
The power source of the reciprocating movement of the thin wall piece is a crank transmission mechanism (2).
本文讨论在己知最小传动角条件下设计曲柄摇杆机构的方法。
This paper discusses the method for designing of crank rocker mechanism under given minimum transmission Angle conditions.
对齿轮传动式、双臂曲柄摇杆式、液压式翻板机的运动状态进行了较深入的分析。
Motion state of the plate turnover machine of gear drive type, double-arm crank rocker type and hydraulic type has been analyzed deeply.
磨盖板机中的盖板传动装置由一个曲柄滑块机构和两个转动导杆机构等组合而成。
The device for driving flat in the flat grinding machine is composed essentially of a slider-crank mechanism and two rotating guide mechanisms.
在论述双曲柄环板式针摆行星传动原理的基础上,提出了受力分析方法,建立了准确的力分析模型。
On the basis of the discussion on the principle of double crank ring-plate-type cycloid drive, the method of force analysis is proposed, and the accurate model of force analysis established.
具有变速传动性能的椭圆齿轮机构串联曲柄滑块机构能够明显改变压力机滑块的运动特性。
The kinematics characteristic of the slide of a press is changed obviously by the ellipse gears and crank mechanism in series.
具有变速传动特性的椭圆齿轮机构串联曲柄滑块机构能够明显改变传统压力机滑块的运动特性。
The kinematics characteristic of a press slide can be changed obviously by the ellipse gears and crank gear in series.
设计的新型三环减速器主要由圆弧齿同步齿形带、小带轮、大带轮、曲柄轴、传动环板、输出轴、外齿轮和箱体等组成。
Newly developed three ring gear reducer is comprised of synchronous belt, big and small pulleys, crankshaft, drive ring plate, output shaft, external gear and case.
探讨了给定行程速比及滑块行程的偏置式曲柄滑块机构具有最佳传动性能的设计方法。
This paper describes the design method of deflection crank slider mechanism of the given stroke velocity rate and slider stroke, which has optimum transmission performance.
本文介绍了糖果裹包机的具有最佳传动角的曲柄摇杆机构的设计,采用微机控制,给出了硬件和软件程序框。
The paper introduces the designs of best transmission angle of crank sliding block mechanism for candy packaging machine controled by computer.
该传动机构由焊接在机架上的导向环和四杆曲柄机构组成。
The transmission mechanism is composed of a guiding ring which is welded on a machine frame, and four rods crank mechanism.
阐述了确定行程速比系数和的平面曲柄摇杆机构最小传动角位置和大小的新方法。
According to its equivalent mechanism-crank rocker mechanism, driving performance and minimum driving Angle position of movable tooth is analyzed.
然后详细的讨论了五杆机构在每一种分类情况下机构中存在双曲柄时机构的传动比及相位角的范围。
Then we conclude the five-bar's classification and the gear ratio and phase Angle in each classification to be full rotatability.
本文分析偏置双曲柄滑块机构的急回运动特性,给出了按最小传动角设计偏置双曲柄滑块机构的设计方法和设计曲线。
The characteristic of quick-return of offset double crank slider mechanism was analyzed in this paper. The synthesis method and curve of this mechanism with minimum transmission angle were presented.
无游梁塔架式胶带传动长冲程抽油机由曲柄-连杆-滑块机构、动滑轮-窄胶带-定滑轮机构和复合滚筒增程机构组成。
The tower type belt driven long stroke pumping unit is composed of the crank-linkage-slide mechanism, movable pulley-narrow belt-fixed pulley mechanism and compound drum stroke-increment mechanism.
无游梁塔架式胶带传动长冲程抽油机由曲柄-连杆-滑块机构、动滑轮-窄胶带-定滑轮机构和复合滚筒增程机构组成。
The tower type belt driven long stroke pumping unit is composed of the crank-linkage-slide mechanism, movable pulley-narrow belt-fixed pulley mechanism and compound drum stroke-increment mechanism.
应用推荐